Bedienungsanleitung DeWalt DW998 T 5 (Seite 24 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549641

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Recommended charging temperature:

approx. 24 °C.

• To charge the battery pack (8), insert it into the

charger (10) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicator (11) will blink.

After approx. 1 hour, it will stop blinking and

remain on. The battery pack is now fully charged.

The battery pack can be removed at any time or

left in the connected charger indefinitely.

Inserting and removing the battery pack

• Insert the battery pack into the pistol grip (7)

until it clicks in place.

• To remove the battery pack, press the two

release buttons (9) simultaneously and pull the

pack out of the pistol grip (7).

Inserting and removing bits (fig. A & B)

Your drill is equipped with a bit holder (6).

• Open the chuck by turning the sleeve (12)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode (fig. C)

This tool can be used in two operating modes:

Drilling:

for steel, wood and plastics.

Hammerdrilling:

simultaneous rotating and impacting for

concrete and masonry drilling operations.

• Select the required operating mode by aligning

the symbol on the mode selector (4) with the

arrow (13) on the housing.

Forward/reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

en - 5 20

ENGLISH

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

Assembly and adjustment

• Prior to assembly and adjustment,

always remove the battery pack.

• Always switch off the tool before

inserting or removing the battery pack.

• Use only DEWALT battery packs and

chargers.

Battery pack (fig. A)

Charging the battery pack

When charging the battery pack for the first time, or

after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles,

the battery pack will attain full capacity. Always check

the mains prior to charging the battery pack. If the

mains is functioning but the battery pack does not

charge, take your charger to an authorised DEWALT

repair agent. Whilst charging, the charger and the

battery pack may become warm to touch. This is a

normal condition and does not indicate a problem.

Do not charge the battery pack at

ambient temperatures <4 °C or >40 °C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW998 T 5 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info