Bedienungsanleitung DeWalt DWD010 (Seite 28 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

500486

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

KEYLESS CHUCK INSTALLATION (FIG. 6)

Screw the chuck on by hand as far as it will go.

Tighten the chuck around the shorter end of a hex

key (not supplied) and strike the longer end in the

clockwise direction with a soft hammer.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

Trigger Switch (ﬁ g. 1)

To start the drill, depress the trigger switch; to stop

the drill, release the trigger switch.

NOTE: Use lower speeds for starting holes without

a center punch, drilling in metal or plastics, driving

screws or drilling ceramics. Higher speeds are better

for drilling wood and composition boards and using

abrasive and polishing accessories.

VARIABLE SPEED

A variable speed trigger switch (a) permits speed

control—the farther the trigger is depressed, the

higher the speed of the drill.

For continuous operation, press and hold the

variable speed switch, move the lock-on button (b)

up, then release the switch.

To stop continuous operation, press the switch

briefly and release it. Always switch the tool off when

work is finished and before unplugging.

Speed Dial (ﬁ g. 1)

DWD014, DWD014S

To reduce the speed, turn the speed dial (g)

counterclockwise. To increase speed, turn the dial

clockwise.

Proper Hand Position (ﬁ g. 7)

WARNING: To reduce the risk of

serious personal injury, ALWAYS

use proper hand position as shown

in figure 7.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand under the

the housing, with the other hand on the main handle

(h).

Drilling

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

1. Use sharp drill bits only. For WOOD, use the

low speed setting and twist drill bits, spade bits,

power auger bits, or hole saws. For METAL, use

the low speed setting and steel twist drill bits or

hole saws.

2. Always apply pressure in a straight line with the

bit. Use enough pressure to keep drill biting, but

do not push hard enough to stall the motor or

deflect the bit.

3. Hold tool firmly with both hands to control the

twisting action of the drill.

CAUTION: Drill may stall if overloaded

causing a sudden twist. Always expect

the stall. Grip the drill firmly to control

the twisting action and avoid injury.

4. IF DRILL STALLS, it is usually because

it is being overloaded or improperly used.

RELEASE TRIGGER IMMEDIATELY, remove

drill bit from work, and determine cause of

stalling. DO NOT CLICK TRIGGER ON

AND OFF IN AN ATTEMPT TO START A

STALLED DRILL — THIS CAN DAMAGE

THE DRILL.

5. To minimize stalling or breaking through the

material, reduce pressure on drill and ease the

bit through the last fractional part of the hole.

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

7. With variable speed drills there is no need to

center punch the point to be drilled. Use a

slow speed to start the hole and accelerate by

squeezing the trigger harder when the hole is

deep enough to drill without the bit skipping out.

DRILLING IN METAL

Start drilling with slow speed and increase to full

power while applying firm pressure on the tool.

A smooth even flow of metal chips indicates the

proper drilling rate. Use a cutting lubricant when

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWD010 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info