Bedienungsanleitung DeWalt DWD112 (Seite 26 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

500490

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

1. Grasp the rear half of the chuck with one hand

and use your other hand to rotate the front half

counterclockwise, as shown in Figure 4. Rotate

far enough so that the chuck opens sufficiently

to accept the desired accessory.

2. Insert the bit or other accessory about 3/4"

(19 mm) into the chuck and tighten securely

by holding the rear half of the chuck and

rotating the front portion in the clockwise

direction. When the chuck is nearly tightened,

you will hear a clicking sound. After 4–6 clicks,

the chuck is securely tightened around the

accessory.

3. To release the accessory, repeat step 1 listed

above.

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to the

chuck and personal injury may result.

KEYLESS CHUCK REMOVAL (FIG. 5)

Tighten the chuck around the shorter end of a hex

key (not supplied) of 1/4" (6 mm) or greater size.

Using a soft hammer or piece of wood, strike the

longer end in the counterclockwise direction. This

will loosen the chuck so that it can be unscrewed

by hand.

KEYLESS CHUCK INSTALLATION (FIG. 6)

Screw the chuck on by hand as far as it will go.

Tighten the chuck around the shorter end of a 1/4"

(6 mm) or larger hex key (not supplied) strike the

longer end in the clockwise direction with a soft

hammer.

Keyed Chuck – DWD112

(ﬁ g. 7, 8)

The DWD112 features a keyed chuck (d). To insert

a drill bit or other accessory, follow the steps listed

below.

1. Open the chuck jaws by turning collar by hand

and insert the shank of the bit about 3/4"

(19 mm) into chuck. Tighten the chuck collar by

hand.

2. Place chuck key in each of the three holes, and

tighten in clockwise direction. It’s important to

tighten chuck with all three holes.

To release the bit, turn the chuck counterclockwise

in just one hole, then loosen the chuck by hand.

REMOVAL OF KEYED CHUCK (FIG. 7)

Tighten the chuck around the shorter end of a hex

key (not supplied) of 1/4" (6 mm) or greater size.

Using a soft hammer, strike the key sharply in the

counterclockwise direction when viewed from the

front of the tool. This will loosen the chuck so that it

can be removed by hand.

KEYED CHUCK INSTALLATION (FIG. 8)

Screw the chuck on by hand as far as it will go.

Insert the shorter end of a hex key (not supplied)

of 1/4" (6 mm) or greater size and strike it in the

clockwise direction with a soft hammer.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Motor Brushes

DEWALT uses an advanced brush system which

automatically stops the drill when the brushes wear

out. This prevents serious damage to the motor.

New brush assemblies are available at authorized

DEWALT service centers. Always use identical

replacement parts.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWD112 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DWD112

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info