500493
26
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
ENGLISH
24
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Side Handle (fi g. 1)
WARNING: To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed and tightened. Failure to do so
may result in the side handle slipping
during tool operation and subsequent
loss of control. Hold tool with both
hands to maximise control.
A side handle (c) is supplied with your drill. The side
handle clamps to the front of the gear case and can
be rotated 360 degrees to permit right- or left-hand
use.
After the side handle is rotated into position, it
should be pushed rearward until the slots (h) on the
lip of the side handle are aligned and fully engaged
with the projecting tabs (i) on the underside of the
gear case. The side handle is then securely clamped
by turning clockwise until tight.
Variable Speed Trigger Switch (fi g. 2)
The variable speed trigger switch (a) permits speed
control. The farther the trigger switch is depressed,
the higher the speed of the drill.
NOTE: Use lower speeds for starting holes, drilling
in plastics or ceramics or driving screws.
Reversing Lever (fi g. 2)
The reversing lever (b), located above the trigger
switch, changes the direction of rotation of the drill
and is used when backing out screws and jammed
drill bits.
To operate the tool in reverse, release the trigger
switch and push the lever to the left (when viewed
from the chuck end).
To operate the drill in forward, release the trigger
switch and push the lever to the right (when viewed
from the chuck end).
Return the reversing lever to the forward position
after all operations in reverse are completed.
Torque Limiting Clutch
This tool is equipped with a torque limiting clutch
that reduces the maximum torque reaction
transmitted to the operator in case of jamming of a
drill bit. This feature also prevents the gearing and
electric motor from stalling. The torque limiting clutch
has been factory-set and cannot be adjusted.
Motor Lock Control (fi g. 1)
Your DEWALT drill comes with an electronic
feature called motor lock control. It is designed to
help prevent the motor from being overloaded in
demanding applications during a stall situation. This
may be encountered when drilling in steel or using
large bits in wood.
As a stall situation presents itself, the motor cycles
on and off for a set period of time. This reduces the
reaction of the stall. Releasing the trigger resets the
motor lock control and the unit will operate in normal
mode when the trigger is depressed again.
Figure 1 shows the instruction label (j) mounted on
the housing. There are two alert modes:
1. Engaged Mode: When a stall situation
presents itself, the light will come on and stay
on as the motor cycles on and off for a set
period of time before the motor lock control
completely shuts the tool down. When the unit
is running in normal mode, there will be no light
2. Problem Mode: A series of continual flashes as
the trigger is pulled indicates that the electronics
are no longer functioning. The tool may still be
able to function without the benefit of motor
lock control but should be serviced as soon as
possible.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DWD221 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info