Bedienungsanleitung DeWalt DWD221 (Seite 27 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

500493

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

WARNING: To reduce the risk of

personal injury, ALWAYS operate

the tool with the side handle properly

installed. Failure to do so may result

in the side handle slipping during tool

operation and subsequent loss of

control. Hold tool with both hands to

maximise control.

WARNING: Do not attempt to tighten

or loosen drill bits (or any other

accessory) by gripping the front part

of the chuck and turning the tool on.

Damage to the chuck and personal

injury may occur.

Proper Hand Position (ﬁ g. 1, 3)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (c), with the other hand on the main

handle (f).

Trigger Switch (ﬁ g. 2)

To run the tool, press the variable speed switch (a).

The pressure exerted on the variable speed switch

determines the tool speed.

If necessary, press the lock-on button (g) for

continuous operation and release the switch. The

lock-on button works only in full speed, forward

rotation.

To stop the tool, release the variable speed switch.

To stop the tool in continuous operation, press the

switch briefly and release it. Always turn the tool off

when work is finished and before unplugging.

Keyless Chuck (ﬁ g. 4–6)

The DWD221 features a keyless chuck (d) for

greater convenience. To insert a drill bit or other

accessory, follow the steps listed below.

1. Grasp the rear half of the chuck with one hand

and use your other hand to rotate the front half

counterclockwise, as shown in Figure 4. Rotate

far enough so that the chuck opens sufficiently

to accept the desired accessory.

2. Insert the bit or other accessory about 3/4"

(19 mm) into the chuck and tighten securely

by holding the rear half of the chuck and

rotating the front portion in the clockwise

direction. When the chuck is nearly tightened,

you will hear a clicking sound. After 4–6 clicks,

the chuck is securely tightened around the

accessory.

3. To release the accessory, repeat step 1 listed

above.

WARNING: Do not attempt to tighten

or loosen drill bits (or any other

accessory) by gripping the front part

of the chuck and turning the tool on.

Damage to the chuck and personal

injury may occur.

KEYLESS CHUCK REMOVAL (FIG. 5)

Tighten the chuck around the shorter end of a hex

key (not supplied) of 1/4" (6 mm) or greater size.

Using a soft hammer or piece of wood, strike the

longer end in the counterclockwise direction. This

will loosen the chuck so that it can be unscrewed

by hand.

KEYLESS CHUCK INSTALLATION (FIG. 6)

Screw the chuck on by hand as far as it will go.

Tighten the chuck around the shorter end of a 1/4"

(6 mm) or larger hex key (not supplied). Strike the

longer end in the clockwise direction with a soft

hammer.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Lubrication

Your power tool requires no additional lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWD221 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info