Bedienungsanleitung DeWalt DWE4120 T 1 (Seite 11 von 40) (Englisch, Französisch)

548035

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

Attaching Side Handle (ﬁ g. 1)

WARNING: Before using the tool,

check that the handle is tightened

securely.

Screw the side handle(c) tightly into one of the holes

on either side of the gear case. The side handle

should always be used to maintain control of the

tool at all times.

Accessories and Attachments

It is important to choose the correct guards, backing

pads and flanges to use with grinder accessories.

Refer to chart at the end of this section for

information on choosing the correct accessories.

NOTE: Edge grinding can be performed with

Type27 wheels designed and specified for this

purpose.

WARNING: Accessories must be rated

for at least the speed recom mended

on the tool warning label. Wheels and

other accessories running over rated

accessory speed may burst and cause

injury. Threaded accessories must have

a M14 hub (DWE4001/DWE4002

M10). Every unthreaded accessory

must have a 22 mm arbor hole. If it

does not, it may have been designed

for a circular saw and should not be

used. Use only the accessories shown

in the chart at the end of this section.

Accessory ratings must be above listed

minimum wheel speed as shown on tool

nameplate.

Mounting Guards

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

CAUTION: Guards must be used with

this grinder.

When using the DWE4050, DWE4051, or the

DWE4120 grinder for cutting metal or masonry, a

Type 1 guard MUST be used. Type1 guards are

available at extra cost from DEWALT distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

see other accessories that can be used with these

grinders.

MOUNTING AND REMOVING (TYPE 27)

ONE-TOUCH GUARD (FIG. 2A)

NOTE: If your grinder is supplied with a keyless

One-Touch guard, ensure the screw, lever, and

spring are fitted correctly before mounting the guard.

1. Press the guard release lever(k).

2. While holding the guard release lever open, align

the lugs(l) on the guard with the slots(m) on the

gear case.

3. Keeping the guard release lever open, push the

guard down until the lugs engage then rotate

them into the groove on the gear case hub.

Release the guard release lever.

4. With the spindle facing the operator, rotate

the guard clockwise into the desired working

position. The guard body should be positioned

between the spindle and the operator to provide

maximum operator protection.

5. For easy adjustment, the guard can be rotated

in the clockwise direction. NOTE: The guard

release lever should snap into one of the

alignment holes(n) on the guard collar. This

ensures that the guard is secure. The guard

can be repositioned the opposite direction by

depressing the guard release lever.

6. To remove the guard, follow steps 1–3 of these

instructions in reverse.

MOUNTING AND REMOVING A FIXED SCREW GUARD

(FIG. 3) (DWE4001, DWE4002)

WARNING: If present, the One-Touch

guard screw, lever, and spring must be

removed before attempting to mount

the a fixed screw guard. The removed

parts must be retained and reinstalled

to use the One-Touch guard. Noting

the position of these parts before

disassembly will aid in reassembly.

1. Place the angle grinder on a table, spindle(b)

up.

2. Align the lugs(l) with the slots(m).

3. Press the guard(f) down and rotate it to the

required position.

4. Securely tighten the screw(o).

5. To remove the guard, slacken the screw.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service centre to repair or replace

the guard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE4120 T 1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DWE4120 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info