Bedienungsanleitung DeWalt DWE4579 T 1 (Seite 45 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

548697

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

When using the DWE4557, DWE4597, DWE4559,

DWE4579, DWE4599 or the DWE4579R grinder for

cutting metal or masonry a Type 1 guard MUST be

used. Type 1 guards are available at extra cost from

DEWALT distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

show other accessories that can be used with these

grinders.

1. Place the angle grinder on a table, spindle up.

2. Release the clamping lock (h) and hold the

guard (d) over the tool as shown.

3. Align the lugs (i) with the notches (j).

4. Press the guard down and rotate it to the

required posiiton.

5. If required, increase the clamping force by

tightening the screw (k).

6. Tighten the clamping lock.

To remove the guard, release the clamping lock.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service center to repair or replace

the guard.

Fitting and Removing a Grinding or

Cutting Disc (ﬁ g. 3–5)

WARNING: Do not use a damaged

disc.

1. Place the tool on a table, guard up.

2. Fit the backing flange (l) correctly onto the

spindle (m) (fig. 3).

3. Place the disc (o) on the backing flange (l)

(fig.4). When fitting a disc with a raised center,

make sure that the raised centre (p) is facing the

backing flange (l).

4. Screw the threaded clamp nut (n) onto the

spindle (m) (fig. 5):

a. The ring on the threaded clamp nut (n) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (n) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (c) and rotate the

spindle (m) until it locks in position (fig. 4).

6. Tighten the threaded clamp nut (n) with the

two-pin spanner supplied. NOTE: Refer to

Fitting and Removing a Grinding or Cutting

Disc with a Keyless Flange when using the

DWE4579R.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (n) with the two-pin spanner.

Fitting and Removing a Grinding or

Cutting Disc with a Keyless Flange

(ﬁ g. 7, 8)

DWE4579R ONLY

1. Perform steps 1–5 of Fitting and Removing a

Grinding or Cutting Disc.

2. Tighten the threaded keyless flange (s) by

turning it by hand clockwise firmly. (Only use a

flawless keyless flange.)

a. Be sure that the printed side of the keyless

flange is facing you.

b. The arrow must point to the index mark

(fig.7).

3. Release the spindle lock.

An undamaged keyless flange can be loosened

by hand when turning the flange ring in an anti-

clockwise direction.

NOTICE: NEVER loosen a tight keyless

flange with pliers. Always use the the

two-pin spanner (t) (fig. 8).

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and the

tool.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE4579 T 1 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DWE4579 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info