Bedienungsanleitung DeWalt DWE4579 T 1 (Seite 13 von 48) (Englisch, Französisch)

548697

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENGLISH

1. Place the angle grinder on a table, spindle up.

2. Release the clamping lock (h) and hold the

guard (d) over the tool as shown.

3. Align the lugs (i) with the notches (j).

4. Press the guard down and rotate it to the

required posiiton.

5. If required, increase the clamping force by

tightening the screw (k).

6. Tighten the clamping lock.

To remove the guard, release the clamping lock.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service center to repair or replace

the guard.

Fitting and Removing a Grinding or

Cutting Disc (ﬁ g. 3–5)

WARNING: Do not use a damaged

disc.

1. Place the tool on a table, guard up.

2. Fit the backing flange (l) correctly onto the

spindle (m) (fig. 3).

3. Place the disc (o) on the backing flange (l)

(fig.4). When fitting a disc with a raised center,

make sure that the raised centre (p) is facing the

backing flange (l).

4. Screw the threaded clamp nut (n) onto the

spindle (m) (fig. 5):

a. The ring on the threaded clamp nut (n) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (n) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (c) and rotate the

spindle (m) until it locks in position (fig. 4).

6. Tighten the threaded clamp nut (n) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (n) with the two-pin spanner.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly. Follow the instructions given in the

Grinding and Cutting Accessory Chart.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and the

tool.

• Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad

for cracks, tear or excess wear, wire brush

for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage

or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool

at maximum no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Secure and support the workpiece.

Use clamps or a vice to hold and

support the workpiece to a stable

platform. It is important to clamp and

support the workpiece securely to

prevent movement of the workpiece

and loss of control. Movement of

the workpiece or loss of control may

create a hazard and cause personal

injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE4579 T 1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DWE4579 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info