Bedienungsanleitung DeWalt DWE6423 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712392

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Lubrication

Your power tool requires no additional lubrication.

Cleaning

NOTE: After the tool is used in metal sanding

applications without dust bag, clean the tool using

low-pressure air.

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your DEWALT product

needs replacement, or if it is of no further use to

you, do not dispose of it with household waste.

Make this product available for separate collection.

Sanding

Start with the coarsest grit size.

As the tool produces small abrasion marks in all

directions, it is not necessary to sand with the grain.

Check your work at short intervals.

Always switch off the tool when work is finished and

before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Replacing the Sanding Pad and the

Speed Limiter Belt (Fig. 4)

Your sander is equipped with a replaceable belt (m)

which is located between the pad (f) and the sander

body (j). It is designed to control the pad speed

while the unit is off the work surface. The belt and

the sanding pad (f) are designed to be consumable

parts and will occasionally need to be replaced.

The sanding pad needs replacement when signs

of wear become evident. Replacement of the belt

is necessary when the pad speed increases very

dramatically when the unit is lifted from the work

surface. These parts are available at extra cost from

your local dealer or authorised D

EWALT service

centre.

1. Holding the platen firmly, remove the four

screws (o) from the bottom of the pad.

2. Remove the pad (f).

3. Replace worn or damaged belt (m) by wrapping

it around the shoulder screw (k) and bearing

retainer (l) as shown in Figure4.

4. Reinstall pad (replace with new pad if

necessary). Replace the four screws (o). Be

careful not to over-tighten screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE6423 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info