Bedienungsanleitung DeWalt DWS520 T 3 (Seite 35 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

546212

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

ENGLISH

1. Set the speed of the plunge saw to level 5.

2. Place the guide rail on a scrap piece of wood.

3. Set the plunge saw on 5 mm cut depth

4. Place the saw on the rear end of the guide rail.

5. Turn the saw on, press it down to the set

cutting depth and cut the splinterguard along

the full length in one contiuous operation. The

edge of the splinterguard now corresponds

exactly to the cutting edge of the blade.

WARNING: To reduce the risk of injury,

ALWAYS secure the guide rail (w) with a

clamp.

Speed Adjustment (ﬁ g. 1)

The speed can be regulated between 1750 and

4000/min using the speed wheel (s). This enables

you to optimise the cutting speed to suit the

material. Refer to the following chart for type of

material and speed range.

Type of Material

to be Cut

Speed

Range

Solid wood (hard, soft) 3–5

Chipboards 4–5

Laminated wood, blockboards,

veneered and coated boards

2–5

Paper and carton 1–3

Wall Cutting (ﬁ g. 7)

1. Place the plunge saw with the outer guard (v)

on a clean, flat floor.

2. Press the shoe (d) with the front side on the

door against the adjusted depth stop.

Dust Extraction (ﬁ g. 1)

Your tool is fitted with a dust extraction outlet (i).

WARNING: ALWAYS connect the

plunge saw to a dust extractor!

WARNING: ALWAYS use a dust

extraction device designed in

accordance with the relevant regulations

regarding dust emission.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

WARNING: If the saw blade is worn

replace it with a new sharp blade.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the unit with dry air as often as dirt is

seen collecting in and around the air

vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

DEWALT offers saw blades specially designed for

your plunge saw.

Consult your dealer for further information on the

appropriate accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWS520 T 3 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info