Bedienungsanleitung DeWalt DWV902MT T 1 (Seite 36 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549679

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ENGLISH

NOTE: If there is any doubt on the condition

of the filters they MUST be replaced. DO NOT

continue use if filters are damaged.

WARNING: Never use compressed

air or a brush to clean filters, otherwise

damage to the filter membrane will

occur which will allow dust to pass

through the filter. If needed, gently tap

against a hard surface or rinse with

room temperature water and let air

dry. Cleaning of the filters is typically

unnecessary, even if the filter is

covered with dust. The automatic filter

cleaning system will maintain maximum

performance and continue to function.

If visual damage to the filter membrane

exists, replace filters. Filters typically

last between six and twelve months

depending on use and care.

To Install Filters

1. Ensure filter seal (aa) is in place and is secure

2. Line up filter threads (z) to vacuum head threads

and using moderate force, turn filter clockwise

until tight.

NOTE: Use care to not damage filter material.

3. Place the vacuum head (c) onto the container

and secure it by closing the canister latches (d).

Lubrication

Your appliance requires no additional lubrication.

Cleaning

WARNING: Never use solvents or other

harsh chemicals for cleaning the non-

metallic parts of the appliance. These

chemicals may weaken the materials

used in these parts. Never let any liquid

get inside the machine; never immerse

any part of the appliance into a liquid.

1. Vacuum the outside of the dust extractor. For

further cleaning use a cloth dampened only with

water and mild soap if necessary.

2. After use dispose of cloth in an appropriate

container.

Storage (ﬁ g. 11)

1. Empty the canister, refer to To Empty Canister

under Operation.

2. Clean the vacuum inside and outside. Refer to

Cleaning.

3. Clean or replace filters, refer to Filters.

4. Store the suction hose and the power cord as

shown in the illustration. Place the unit in a dry

room and secure it from unauthorized use.

NOTE: Plug inlet plug (s) into inlet (j) to keep

debris inside canister when suction hose is

removed. You can also attach the ends of the

hose together and lock together with the twist-

lock end.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this appliance

could be hazardous. To reduce the risk

of injury, only DEWALT recommended

accessories should be used with this

product.

ACCESSORIES

DWV9340-XJ Filter

DWV9315-XJ Crush-proof hose

DWV9316-XJ Anti-static hose

DWV9401-XJ Paper bag

DWV9400-XJ Plastic liner

DWV9402-XJ Fleece bag

DWV9500-XJ Vac Rack

DEWALT AirLock System

DWV9000 Twist-Lock

connection

DWV9110 29-35mm tapered

rubber adapter

DWV9120 35-38mm stepped

rubber adapter

DWV9130 35mm OD adapter

DWV9150 35mm OD angle

adapter

VAC RACK DWV9500 INSTALLATION (FIG. 11, 12)

NOTE: The DWV902MT comes with DWV9500 vac

rack attachment already installed,

1. Remove the 4 carry handle screws using a T-25

star bit and remove the carry handle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWV902MT T 1 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info