Bedienungsanleitung Digihome 32875F (Seite 18 von 31) (Englisch)

499249

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

English - 18 -

After APS is nalized, the programme table will appear

on the screen. In the programme table you will see

the programme numbers and names assigned to the

programmes.

Manual Channel Scan

In manual channel scan, the number of the multiplex is

entered manually and only that multiplex is searched

for the channels. For each valid channel number, signal

level and signal quality are shown on the screen.

In both manual and auto search any existing channel

in the database is not re-stored to avoid redundant

duplicates of that channel.

Clear Service List (*)

(*) This setting is visible only when the Country option

is set to Denmark, Sweden, Norway or Finland.

Use this setting to clear channels stored. Press “

” or “ ”

button to select Clear Service List and then press OK. The

following OSD message will be displayed on the screen:

Press OK to cancel. Select Yes by pressing “ ” or “ ”

button and press OK to delete all of the channels.

First Time Installation

The user can use this item to load default settings,

which were loaded to the receiver at the factory.

To install factory settings, highlight “First Time

Installation” menu item and press “OK” button,

then you will be asked whether or not to delete the

settings. Selecting “Yes” by pressing “OK” button

while the “Yes” is highlighted will delete the existing

channel table.

Then you will be asked to conrm for deleting all

channels and settings:

By selecting Yes and pressing the “OK” button, the

existing channel table will be deleted. After factory

settings are loaded, “First Time Installation” menu

will be displayed.

The menu which is displayed for language selection

appears on the screen at rst. By using “

” or “ ”

buttons, select the desired language option, and press

OK button to activate.

After then, “First time installation” OSD will appear

on the screen. By pressing “

” or “ ” buttons, select

the Country you want to set and press “OK” button

(* only for EU countries).

Press the “OK” button to start installation. After search

is completed for digital channels, a message asking

whether to search for analogue channels appears

on the screen.This process is same as described in

Automatic Search section..

Media Browser

• To display Media Browser window, press either

“MENU” button on the remote control and then

select Media Browser by pressing “ ” or “ ” button.

Press OK button to continue. Media Browser menu

contents (depending on the contents of your USB

drive) will be displayed.

• Also, when you plug a USB device, the following

screen will be displayed:

Select YES by pressing “ ” or “ ” button and press

OK button. Media browser will be displayed.

• You can play music and picture les from a USB

memory stick.

Note: If you plug USB stick while in analogue mode, the TV

will automatically switch to digital TV mode.

Note: Some USB compliant devices may not be supported.

Note: If the USB stick is not recognized after power off/on

or First Time Installation, rst, plug the USB device out and

power off/on the TV set. Plug the USB device in again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Digihome 32875F Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info