Bedienungsanleitung Dik Geurts Instyle 1000 (Seite 44 von 112) (Deutsch, Englisch, Holländisch, Französisch)

695341

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

INSTALLATION MANUAL

9.7.2 Instyle Tunnel / Prostyle Tunnel

9.7.2.1 Air slide valve

Pior to installing the appliance, check the operation of the air slide (see appendix 2, fig. 20a and 20b). It is possible

that steel grit ended up in the air slide during transportation. If the air slide does not run smoothly, it has to be

cleaned. For this, the air slide should be disassembled. The suspended air slide valve is spring-mounted using a

bolt and a spring, which are located below the cover plate.

When disassembling the air slide, proceed as follows (see appendix 2, fig. 20a and 20 b):

!Caution

Has an outside air connection been mounted? If so, this should be removed first (see appendix 2, fig. 20b and

section 9.7.2.2).

Remove the vermiculite plates from the bottom (see chapter 9.7.3.2.1).

Unscrew the 5 Allen screws of the cover plate from the bottom and remove them.

Unscrew the Allen screw with spring.

Remove the air slide by bringing it towards you.

Check the air slide and clean it if necessary.

For placing back the air slide, the actions described for disassembling should be performed in reverse order.

9.7.2.2 Outside air connection

It is possible to provide the appliance with an outside air connection. This outside air connection is optionally

available (as an external kit). This kit can be used for a connection on the bottom of the appliance and is available

through your supplier.

!Caution

It is possible that the outside air connection is pre-mounted at delivery. This will be the case for an RS (room

sealed) version. Observe the steps as described under the heading 'Outside air connection pre-mounted'.

When assembling the outside air connection, proceed as follows:

Outside air connection not pre-mounted (see appendix 2, fig. 21):

Remove the lever at the bottom of the appliance by loosening the 2 screws and removing them.

Remove the 4 screws at the bottom of the appliance.

Place the tray with mounted pipe opening against the bottom of the appliance.

Re-use the 4 screws to mount the tray.

Place back the lever and fasten it by means of the 2 screws.

Connect the flexible hose (Ø 80 mm) to the round pipe opening of the outside air connection.

!Caution

In case of a fully closed system, always ensure an air-tight connection of the flexible hose to the round pipe

opening by using a heat resistant sealant.

For disassembling the outside air connection, please observe the above-mentioned steps in reverse order.

Outside air connection pre-mounted (see appendix 2, fig. 22):

Connect the flexible hose (Ø 80 mm) to the round pipe opening of the outside air connection.

!Caution

In case of a fully closed system, always ensure an air-tight connection of the flexible hose to the round pipe

opening by using a heat resistant sealant.

For disassembling the outside air connection, please observe the above-mentioned steps in reverse order.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Instyle 1000 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Instyle 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info