Bedienungsanleitung Dik Geurts Prostyle 1000V (Seite 43 von 112) (Deutsch, Englisch, Holländisch, Französisch)

695350

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

INSTALLATION MANUAL

9.7.1.2 Air slide valve

With installation and maintenance of the appliance check the operation of the air slide valve (see Appendix 2,

Fig. 18). There is the possibility that steel grit entered the air slide valve during transport. If the air slide valve does

not move smoothly it must be cleaned. The air slide valve must be disassembled to do this. The air slide valve is

suspended sprung by means of a bolt and a spring located below the cover plate.

Proceed as follows when disassembling the air slide valve (see Appendix 2, Fig. 18):

Remove the vermiculite plates and the felt from the bottom (see section 9.7.1.3.1).

Remove the 5 cover plate socket screws from the bottom.

Remove the cover plate.

If there is an outside air connection remove the 2 screws from the front strip.

!Caution

You only have to remove the front strip if an exterior connection is assembled.

Remove the socket screw with spring.

Remove the air slide valve by bringing it towards you.

Check the air slide valve and clean it if necessary.

To replace the air slide valve proceed as described for removal in reverse order.

9.7.1.3 Interior lining

9.7.1.3.1 Vermiculite

The fire’s vermiculite plates are located on the bottom against the rear wall and/or side walls of the appliance. In

the following situations the vermiculite plates must be taken out:

• When disassembling the air slide valve (see section 9.7.1.2).

• To be able to reach the adjustable legs (see section 9.6).

• When replacing the vermiculite plates.

The bottom plates and the underlying felt are first removed and the rear plates last. The insertion of the

vermiculite plates takes place in reverse order.

!Caution

Make sure that the vermiculite plates are replaced in the original position! The back plate with the small, not

countersunk, holes must be placed to the front.

9.7.1.3.2 Flame baffle plate

On delivery the flame baffle plate (see appendix 2, fig. 19) is located in the top section of the appliance. The flame

baffle plate must be removed in a number of situations:

• when mounting and checking the flue gas exhaust connection;

• when performing maintenance at the flue duct;

• when replacing the flame baffle plate.

For removing the flame baffle plate, proceed as follows:

Lift the left side of the flame baffle plate until it gets above the edge and slide the flame baffle plate to the right.

Lower the left side of the flame baffle plate and slide the flame baffle plate to the left.

Slide the right-hand side of the flame baffle plate over the edge.

Slide the flame baffle plate to the left and lower it until it reaches the lower section of the appliance.

Now you can remove the flame baffle plate.

Placing the flame baffle plate takes place in reverse order.

!Caution

The stainless steel profile must be placed at the front with the screw heads on top (see appendix 2, fig. 19).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Prostyle 1000V Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Prostyle 1000V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info