Bedienungsanleitung Dik Geurts Prostyle 700 (Seite 41 von 112) (Deutsch, Englisch, Holländisch, Französisch)

695339

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

INSTALLATION MANUAL

When replacing the cord proceed as follows:

Open the door.

Remove the cord and the mastic from the recess.

Apply a new layer of heat resistant mastic in the recess where the cord was.

Place a new cord in the recess. Do this loosely and do not pull the cord tight.

Insert both ends of the cord in the special sleeve.

The cord, the sleeve and the mastic are available through your supplier.

!Caution

Make sure that the sleeve is placed on the underside of the glass pane.

The door can also be adjusted in height. There are 2 eyelets on the upper pin on which the door is hung.

Removing 1 or more of these eyelets allows the door to fall to the desired level.

Proceed as follows when adjusting the door handle:

Loosen the 2 hexagonal pin nuts around which the handle of the door falls a few turns (see Appendix 2, fig. 8a

(Instyle and Prostyle 700) and 8b (Instyle and Prostyle 700). This pin ensures that the door is tightly clamped.

Adjust the pin.

Tighten the 2 hexagonal nuts again.

Test the sealing of the door (see the start of this paragraph).

Repeat this process if the result is not satisfactory.

9.4 Glass pane(s)

!Caution

• Avoid damage when removing/fitting the glass pane(s);

• Avoid/remove fingerprints on the glass pane(s) because these burn in.

Tip!

Use the supplied pane window cleaner to remove fingerprints/dirt on the glass pane(s).

9.4.1 Disassembly of glass pane in door(s)

To remove the glass pane in the door(s) follow the instructions below:

(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle applianc: see Appendix 2, fig. 10).

!Caution

When you install an Instyle or Prostyle Tunnel: Follow the instructions below. Then repeat these instructions on

the other side of the appliance.

Open the door.

Lift the door out by first sliding it upwards, then tilt it slightly forwards and allow it to lower.

Place the door on a flat surface.

Remove the nuts from the strips.

Remove the strips.

Lift the glass pane out. The pane seal is then also taken out.

Tip!

• When replacing the glass pane always replace the seal in the door (= seal between the glass pane and the

door).

• Check the door sealing cord and replace if necessary (see paragraph 9.3).

9.4.2 Assembly of glass pane in door(s)

Assemble the glass panes in the door(s) according to the steps described in paragraph 9.4.1 ‘Disassembly of glass

pane in door(s)’ but in reverse order.

(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle appliance: see Appendix 2, fig. 10).

!Caution

Assembly of the door(s) is somewhat different.

Proceed as for assembly of the door(s):

Bring the hole at the bottom of the hinging part of the door exactly below the lower pin.

Slide the door up. The pin slides into the lower hole.

Bring the hole at the top of the hinging part of the door exactly above the upper pin and allow the door to lower.

The pin slides into the upper hole.

The door is now assembled.

!Caution

• Do not fasten the bolts too tight to avoid breaking off and/or stripping: overtightening will cause breakage.

• Place the glass pane (including new pane seal) with the logo to the bottom right.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Prostyle 700 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Prostyle 700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info