Bedienungsanleitung Dik Geurts Vidar Triple-wall (Seite 24 von 76) (Deutsch, Englisch, Holländisch, Französisch)

695365

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

INSTALLATION MANUAL

5.3.1 HETAS amendments

Health and safety precautions

Special care must be taken when installing the stove such that the requirements of the Health and Safety at Work

Act are met.

Handling

Adequate facilities must be available for loading, unloading and site handling.

Fire Cement

Some types of fire cement are caustic and should not be allowed to come into contact with the skin. In case of

contact wash immediately with plenty of water.

Asbestos

This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the course of installation then

please seek specialist guidance and use appropriate protective equipment.

Metal Parts

When installing or servicing this stove care should be taken to avoid the possibility of personal injury.

Note of references to the current UK regulations

In all cases the installation must comply with current Building Regulations, Local Authority Byelaws and other

specifications or regulations as they affect the installation of the stove. It should be noted that the Building

Regulations requirements may be met by adopting the relevant recommendations given in British Standards BS

8303, BS EN 15287-1:2007 as an alternative means to achieve an equivalent level of performance to that obtained

following the guidance given in Approved Document J.

Please note that it is a legal requirement under England and Wales Building Regulations that the installation of the

stove is either carried out under Local Authority Building Control approval or is installed by a Competent Person

registered with a Government approved Competent Persons Scheme. HETAS Ltd operate such a Scheme and a

listing of their Registered Competent Persons can be found on their website at www.hetas.co.uk.

This stove must not be installed into a chimney that serves any other heating appliance. More detailed advice

about existing chimney usage.

!Note

A chimney height of not less than 4.5 metres measured vertically from the outlet of the stove to the top of the

chimney should be satisfactory. Alternatively the calculation procedure given in EN 13384-1 may be used as the

basis for deciding whether a particular chimney design will provide sufficient draught.

The outlet from the chimney should be above the roof of the building in accordance with the provisions of

Building Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other faults which might

allow fumes into the house. Older properties, especially, may have chimney faults or the cross section may be too

large i.e. more than 230 mm x 230 mm. Remedial action should be taken, if required, seeking expert advice, if

necessary. If it is found necessary to line the chimney then a flue liner suitable for solid fuel must be used in

accordance with Building Regulations Approved Document J.

Any existing chimney must be clear of obstruction and have been swept clean immediately before installation of

the stove. If the stove is fitted in place of an open fire then the chimney should be swept one month after

installation to clear any soot falls which may have occurred due to the difference in combustion between the

stove and the open fire.

If there is no existing chimney then any new system must be to the designation described above and in

accordance with Building Regulations Approved Document J.

A single wall metal fluepipe is suitable for connecting the stove to the chimney but is not suitable for use as the

complete chimney. The chimney and connecting fluepipe must have a minimum diameter of 150 mm and its

dimension should be not less than the size of the outlet socket of the stove.

Any bend in the chimney or connecting fluepipe should not exceed 45°. 90° bends should not be used.

Combustible material should not be located where the heat dissipating through the walls of fireplaces or flues

could ignite it. Therefore when installing the stove in the presence of combustible materials due account must be

taken of the guidance on the separation of combustible material given in Building Regulations Approved

Document J and also in these stove instructions.

If it is found that there is excessive draught in the chimney then a draught stabiliser should be fitted. Fitting of a

draught stabiliser will affect the requirement for the permanent air supply into the room in which the stove is

fitted in accordance with Approved Document J (see also combustion air supply).

Commissioning and handover

Ensure all parts are fitted in accordance with the instructions.

On completion of the installation allow a suitable period of time for any fire cement and mortar to dry out, before

lighting the stove. Once the stove is under fire check all seals for soundness and check that the flue is functioning

correctly and that all products of combustion are vented safely to atmosphere via the chimney terminal. On

completion of the installation and commissioning ensure that the operating instructions for the stove are left with

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Vidar Triple-wall Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Vidar Triple-wall

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info