Bedienungsanleitung Dimplex Albany Opti-myst (Seite 14 von 36) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

706563

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen

if the heat outlet is restricted in any way. If the cut-out operates, unplug the ﬁ re from the socket outlet and allow

approximately 10 minutes before reconnecting. Before switching the ﬁ re back on remove any obstruction that may be

restricting the heat outlet, then continue normal operation.

Tips for using your appliance.

1. Only pull out the drawer when its time to reﬁ ll the water tank or change a lamp, otherwise it may lead to excess

water in the sump and reduced ﬂ ame effect. If this happens empty the water from the sump as instructed under

‘Maintenance’.

2. With the ﬂ ame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as

long than when it is at maximum ﬂ ame setting.

3. Do not tilt or move the ﬁ re while there is water in the tank or sump.

4. Make sure that the ﬁ re is on a level ﬂ oor.

5. The ﬂ ame control knob ‘C’ (Fig.2) may be turned up or down to give a more realistic effect.

6. Sometimes the ﬂ ames appear more real when the ﬂ ame control knob is turned down.

7. Give the ﬂ ame generator some time to react to changes you may make on the ﬂ ame control knob.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE

Changing lamps.

If a large amount of the smoke appears grey or colourless it may be that one or more lamps have failed.

You can check for lamp failure as follows.

1. Leaving the ﬂ ame effect on, open the drawer fully, gently pull the drawer fully out by the tab. (See Fig.3)

2. View the lamps from a distance in front of the ﬁ re and observe which lamp needs to be changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the ﬁ re from the mains.

4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.

5. Remove the water tank by lifting upwards and place in a sink.

6. Remove the sump as described in the Cleaning Section.

7. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder, (See Fig.4

and 5). Replace with an original, 12V, 45W, Gu5.3 base, 8º beam angle, coloured lamp. Purchase the lamps from your

local supplier.

8. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push ﬁ rmly in place. (See Fig.4

and 5).

9. Replace the sump and water tank and carefully close the drawer.

10. Switch on.

Filling the water tank.

When the water tank is empty, ﬂ ame and smoke effect shuts off, and you will hear 2 audible ‘beeps’. Follow these

steps to reﬁ ll:

1. Press Switch ‘A’ to (0). (See Fig.2)

2. Pull out the drawer as far as possible by the tab. (See Fig.3)

3. Remove the water tank by lifting upwards and outwards.

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (See Fig.6)

5. Fill tank with tap water with a maximum hardness of 10Dh only. This is necessary to prolong the life of the ﬂ ame

and smoke producing unit.

In situations with a higher water hardness, the water should be ﬁ ltered (for example with a Maxtra ﬁ lter). Do not use

a decalciﬁ er.

6. Screw the cap back on, do not overtighten.

7. Return the tank to the sump, with the tank cap facing down and the ﬂ at side of the tank facing outward.

8. Press Switch ‘B’ once to turn on ﬂ ame effect. (See manual control section and Fig.2).

9. Press Switch ‘A’ to ‘ON’ ( I ) position. (See Fig.2)

10. Gently push the drawer back in as far as it will go.

Cleaning.

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE Fire.

We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-

Water Tank, Sump and Seal, Sump lid, Tank cap and seal, Air ﬁ lter.

For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or

ﬂ uff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan ﬁ re.

Water tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in

the outer groove and the centre rubber seal.

3. Put a small quantity of washing up liquid into the tank, reﬁ t the cap and shake well, rinse out until all traces of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Albany Opti-myst Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info