Electronic Climate Control - see Fig. 5
(ROF2ECC & ROF3ECC models only)
Operation
The electronic control allows MANUAL and AUTO operation. In manual
on mode there are three heat settings LOW
AUTO mode the heater comes on as per the programmed timer settings
(See Setting programs).
being produced, the ‘ ’ neon is lit - see Fig. 5 .
Initial Operation
When the heater is connected to the mains the ‘ ’ neon will be lit and
the display is blank. Press the ‘ ’ button and the display goes to full
heat set to 35o C - see Fig. 13 .
Note: Fig. 18 .
St
With the heater ON if the ‘ ’ button is pressed, the heater will go into
standby mode, heater switches off, the display goes blank and only the
MAINS ON neon ( ) remains lit. On pressing the ‘ ’ button again the
heater will come on in the mode and with the settings it had prior to
going into standby mode.
Setting Time
T ’
see Fig. 14 .
1. Press the ‘ ’ or ‘ ’ until the correct time is displayed.
2. Press ENTER. The display will return to the state prior to entering
set time.
N.B. If no keys are pressed after 4 minutes the display will revert to the
state prior to entering set time.
Manual Operation
Pressing ‘ ’ from the default HIGH screen ( Fig. 13 ) brings the heater
into AUTO mode - see ‘Setting the Timer Programs’. Press again to put
the heater into OFF mode. Press again for LOW heat (Fig. 12 ). Press
again for MEDIUM heat. Press again brings the user full circle to HIGH
heating mode.
Setting the Desired T
The desired temperature can be set using the ‘ ’ or ‘ ’ keys. The
temperature can be set from 5o C to 35o C and this will be shown on the
display
switch OFF . If the ambient temperature drops the heater will come on
again automaticallyOFF and ON is a staged switching,
to conserve energy and assist with temperature regulation e.g. if the
heater is set to HIGH heat and the temperature is set to 28o C, at 26o C
the heater will switch to MEDIUM heat, at 27o C the heater will switch
to LOW heat. Then at 28o C the heater will switch OFF completely
Setting the Timer Programs
T program settings are possible, P1 and P2 . Only HIGH heat is
possible for program settings. Press ‘ ’ twice, P1 AUTO ON and a time
will flash - see Fig. 15 . The first P1 ON time can now be set:
1. Press the ‘ ’ or ‘ ’ buttons to set the time.
2. Press ‘ ’.
Now P1 AU off is displayed, P1 OFF time can now be set:
3. Press the ‘ ’ or ‘ ’ buttons to set the time.
At this point either :
(a) press ‘ ’ to exit the Program mode and return to
AUTO mode. The heater is now in AUTO mode. The heater will
switch ON and OFF depending on programme P1 previously
entered.
OR
(b) press ENTER to set the ON and OFF times for program
2, as in steps 1 to 3 above.
At this point press ENTER or PROG to exit the Programme mode. The
heater is now in AUTO mode. The heater will switch ON and OFF
depending on programme P1 & P2 previously entered. If after
programming and returning to the AUTO mode displayP1 or P2 is
active, the display will show PROG 1 AUTO ON or PROG 2 AUTO ON
depending on which is active - see Fig. 16 . An OFF time cannot be
entered which is less than the corresponding ON time. When setting
the timer programs if no keys are pressed, the display will (after 4
minutes) revert to the previous display i.e. display prior to entering
Program mode.
Run Programs
If MODE is pressed until AUTO appears on the screen (either AUTO-
ON or AUTO-OFF), the heater will run both P1 and P2 program as they
are set.
NOTE: The heater cannot be programmed to run P1 only or P2
only
TP1 , set P1 OFF time to be same as P1 ON time. TP2
set P2 OFF time to be same as P2 ON time.
Review Program settings
TAUTO mode.
Press ENTER and the times for PROG 1 ON, PROG 1 OFF
ON and PROG 2 OFF will be displayed consecutively for 2 seconds.
The display will automatically return to the state it was in before ENTER
was pressed.
FROST Protection Mode
With the heater in any mode, OFF or AUTO, if the
displayed set temperature is reduced to 5o C the heater will go into FROST
Protection mode - see Fig. 17. In this mode only
temperature drops below 5o C, will the heater come on.
freezing. In FROST Protection mode the heater comes on in the high
heat mode only‘ ’ button is the only way to bring the
heater out of this special mode.
Remote Control Operation - see Fig. 19
The batteries for the remote control are not installed in the remote but
are packed separately in the carton.
diagrams behind battery cover on the remote control.
The remote allows the set temperature to be adjusted, the mode to be
selected or can be used to put the heater in FROST Protection mode.
Press the ‘ ’ button on the Remote Control to go from OFF
High and back to OFF again. Press the ‘ ’ or ‘ ’ buttons on the remote
to set desired temperature between 5o C and 35o C. Press the ‘’ button
to put the heater into FROST Protection mode. Pressing the ‘ ’ button
(on the Remote Control) is the only way (using the Remote Control) to
bring the heater out of this mode i.e. pressing the ‘ ’ or ‘ ’ buttons on
the remote will have no effect on the heater
Discard leaking batteries
Dispose of batteries in the proper manner according to Provincial and
local regulations.
battery type, if inserted incorrectly
the same time, if disposed of in a fire or if an attempt is made to charge
a battery not intended to be recharged.
Storage
If the radiator is not required for long periods, for example during the
summer
prevent the accumulation of dirt and dust. The supply cable can be
stored in the cable storage area provided - see Fig. 20. The supply
cord should be neatly coiled around the hooks provided ensuring that
the plug does not trail on the floor
compartment.
IMPORT
The heater must be kept plugged in at the mains to retain the time and
the programmed settings. If unplugged from the mains, resetting the
time and the programmed settings will be necessary
Safety in Use
This appliance incorporates a number of safety devices. In addition to
the ‘Important Safety
following;
Tilt Switch
The tilt switch will prevent the heater from working if it is accidentally
tipped over on its side.
If the radiator is tipped over while it is hot, disconnect the power and
allow it to cool, then stand the radiator back upright. Reconnect the
power - normal operation should be resumed. If the radiator does not
heat up again, it is possible that the thermal safety cut-out has operated
- see below
Safety Overheat Protection
The heater is fitted with a thermal safety cut-out which will switch off the
heater should it overheat for any reason. If the cut-out
operates it is the result of abnormal overheating, and the Customer
Services Helpline should be contacted for further advice.
