Bedienungsanleitung Dimplex DABKT10 (Seite 5 von 12) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

520599

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Installation and Operating Instructions

Kit Reference Suitable Models

CABKT10 CAB10E, CAB10W & CAB10A

CABKT15 CAB15E, CAB15W & CAB15A

DABKT10 DAB10E, DAB10W & DAB10A

DABKT15 DAB15E, DAB15W & DAB15A

The kit comprises of: -

· 1 egg crate grill assembly

· 1 recessed duct (unformed)

· Duct endcaps

2 off (LH & RH) for CAB10\15 & DAB10

4 off for DAB15

· Bag containing screws:

8 off for CAB10\15 & DAB10

14 off for DAB15

This installation instruction must be read in

conjunction with the instruction manual of the Air

Barrier being installed and form an addendum to that

document.

The kit is designed to facilitate installation of one of

the above Air Barrier models into a ceiling void.

The maximum effective height from floor to ceiling

into which the Air Barrier is being fitted is 2.5m for

the CAB series and 3.5m for the DAB series.

The ceiling can be either of a plasterboard (or similar)

construction, or of suspended 600 x 600mm tiles.

Installation in a plasterboard (or similar) Ceiling

First it is necessary to ensure that sufficient space exists above the

ceiling for the Installation of the Air Barrier (see Table 1 below).

Table 1

CAB10 CAB15 DAB10 DAB15

X 1205 1805 1205 1805

Y 605 605 605 605

Z 360 MIN. 360 MIN. 460 MIN. 460 MIN.

A hole as indicated in Fig. 1 must be cut into the ceiling, central to and

as close to the doorway as possible ( i.e. minimise ‘W’ - see Fig. 1).

It may be necessary to fix an internal supporting frame around the

newly cut aperture.

The grille frame ‘a’ can then be fixed in position (see Fig. 1).

Assembly of Recessed Duct Kit

Using the duct endcaps as a guide, form the duct by hand into

correct shape - see ‘b’ in Fig. 2. Screw fix the duct to endcaps using

the screws provided.

Finally bend up tabs as shown in Fig. 3.

In order to fit the Air Intake Duct, first remove outlet grille, bottom

panel and then the Intake grille assembly - as shown in Fig. 4 .

Refer to ‘CAB/DAB Installation & Operating Instructions’.

The intake air duct can then be positioned using the tabs shown in

Fig. 3 and located in position as detailed in Fig. 5 using the supplied

screws fastened into the endcap.

Note: It is not necessary to replace the intake grille assembly.

Dimplex Air Barrier - Recess Kit

Models : CABKT10, CABKT15, DABKT10 & DABKT15

The Air Barrier can then be mounted into the ceiling void

(using lengths of threaded bar or hooks screwed into the threaded

inserts located in the top side of the appliance) with the Air Outlet

positioned centrally above the door as in the ‘X’ dimension and as

close to the supplied Grille Frame in the ‘Z’ dimension (150mm max.)

as shown in Fig.1.

The appliance is also required to be positioned as close to the door

opening as possible in the ‘Y’ dimension as shown in Fig. 1 and

inside the grille opening as shown in Fig. 6 to achieve optimum

air-flow effect.

The Air Barrier supplies (Electric or Water) are then made as per

‘CAB/DAB Installation & Operating Instructions’.

The bottom panel and outlet grille can then be replaced, and the outlet

vanes positioned straight down.

The installation of the Air Barrier should be carried out by a

competent electrician and be in accordance with the current IEE

wiring regulations before re-inserting the egg crate grille into the

grille frame.

Installation in a Suspended Ceiling

First it is necessary to ensure that sufficient space exists above the

ceiling for the Installation of the Air Barrier - see Table 2.

Table 2

CAB10 CAB15 DAB10 DAB15

X 2 x Ceiling tiles 3 x Ceiling tiles 2 x Ceiling tiles 3 x Ceiling tiles

Y 1 x Ceiling tile 1 x Ceiling tile 1 x Ceiling tile 1 x Ceiling tile

Z 360 MIN. 360 MIN. 460 MIN. 460 MIN.

The required tile width needs to be left open (central to, and as close

as possible to the doorway i.e. with no central Ceiling tile support

bar).

The Air Barrier can then be installed in the ceiling void as detailed in

‘Installation in a plasterboard Ceiling’ and in the ‘CAB/DAB Installation

& Operating Instructions’.

The egg crate grille core only may then be inserted directly into the

tile aperture left open.

Thermal Safety cut outs

The power supply to the heating elements will be interrupted if one

or a combination of the following abnormal events occur:

1. Air intake duct or outlet grilles are obstructed.

2. Internal ventilation is impaired due to build up of dust and

fluff.

3. Blower unit stalls.

To reset the thermal safety cut-outs, access reset buttons (see ‘x’ in

Fig. 7) by removing the intake duct. Before re-setting the reason for

activation must be determined and corrective action taken.

Cleaning

WARNING: DISCONNECT SUPPLY before carrying out

maintenance.

External appearance can be maintained by wiping occasionally with

a damp cloth ; for stain removal, a weak soap solution can be applied

with a cloth and the surface wiped dry. Care must be taken to avoid

any moisture ingress into the product.

After Sales Service

Should you require after sales service, please get in touch with the

supplier through whom you purchased the appliance.

(1)

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Dimplex DABKT10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info