Bedienungsanleitung Dimplex DEE 2103 (Seite 14 von 38) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

520634

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Installation instructions

Install the continuous-ﬂow heater as described in the

illustrated section. Observe the instructions in the text.

Safety information

Risk of electric shock!

Switch off the mains voltage supply immediately if

a fault occurs.

We do not accept liability for damage resulting from

■

failure to heed these instructions.

The continuous-ﬂow heater may only be connected

■

and put into operation by a qualiﬁed professional.

Never open the appliance without disconnecting the

■

power supply beforehand.

The statutory regulations of the respective country, as

■

well as those of the local electricity and water suppliers,

must be adhered to.

The continuous-ﬂow heater is a Class

■ I appliance and

must be connected to the protective earth.

The appliance must be permanently connected to in-

■

stalled pipes. The conductor cross-section must comply

with the installed appliance power.

Caution

■ : Earthed water pipes may give the appearance of

a connected protective earth.

To guarantee compliance to relevant safety regulations,

■

an all-pole separator must be ﬁtted during installation.

The contact opening must be at least 3 mm.

The continuous-ﬂow heater is only suitable for closed

■

(pressurized) operation.

The tap and outlet ﬁttings must be approved for operation

■

with closed (pressurized) continuous-ﬂow heater systems.

The continuous-ﬂow heater can be operated with cold or

■

pre-warmed water (for example, from a solar energy unit

water supply). Observe the technical data and the special

accessories for this purpose.

Only connect the continuous-ﬂow heater to a cold water

■

line.

The continuous-ﬂow heater may only be installed in a

■

frost-free room.

Disconnect the electrical connection cable from the

■

supply and shut off the water supply before connect-

ing the appliance!

Connect the water supply and then connect the elec-

■

trical supply.

Only make the openings which are required for instal-

■

lation on the rear of the appliance. If the appliance is

reinstalled, the unused openings must be provided with

watertight sealing.

Do not touch electrically live parts after installation.

■

Installation

Unpacking/Removing the cover

Unpack the appliance and check for transport-related ■

damage.

Please dispose of the packaging, and if applicable, the old

■

appliance in an environmentally-friendly manner.

II.

Preparations for installation

Important: Only use the supplied installation set.

The supplied water connection nozzles must be installed!

Shut off water supply. The electrical connection (connec-

■

tion cable) must be disconnected from the power supply.

Unscrew the fuse or switch off the circuit breaker.

III.

Wall mounting

The continuous-ﬂow heater must be mounted on the ■

wall. Attach it if necessary on the lower adjustable screws.

The distance to the wall is variable. You can compensate

■

for any unevenness of the wall's surface.

The grommet must tightly surround the connection cable.

■

If it is damaged during mounting, the openings must be

provided with watertight sealing.

IV.

Water connection

The continuous-ﬂow heater must be vented. The ■

warm water tap must be opened and the appliance

must be ﬂushed out thoroughly for 1 minute with

at least 6 litres of water.

Electrical connection/Mounting

The electrical supply terminal can be ﬁtted at the top or ■

bottom. The sheath of the connection cable must extend

for at least 40 mm into the appliance.

VI.

Startup/additional information

First start-up

Switch on the fuses.

■

Setting the temperature. ■

Starts rinsing: Open the warm water tap and allow water ■

to ﬂow for at least 1 minute (ﬂow-rate at least 6 litres per

minute). Only then (for safety reasons) will the appliance

begin to heat.

Tip: Should the appliance not start because of a reduced

ﬂow-rate, remove the perlator, shower head or similar before

start and repeat the process.

Remove the ﬂow-rate limiter (see Fig. A) with low water

■

pressure.

Explain the operation of the continuous-ﬂow heater to

■

the user.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex DEE 2103 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info