Bedienungsanleitung Dimplex DX431 (Seite 8 von 37) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

798183

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

EN-8

English

DX 421, DX 422T, DX 431, DX 432T, DX 432T

5.1 Fan operation (device type DX 422T)

Switch F switches on a fan which causes faster heat

distribution through increased air recirculation.

The fan can also be used as cold air fan.

In cold air fan operation, turn the thermostat rotary

knob to the maximum (clockwise).

5.2 Fan Operation (device type DX 432T & DX432Ti)

turbo switch in it’s Off position ( neon off ) there is no heat

output from the convector. With the I / II switch still in the

I position you can have 1kw output but only with the turbo

boost On (neon on). To get an output of 2kW leave the

turbo switch off and set the I / II switch to position II.

(Note 2kw is only possible with turbo Off). To achieve

3kw output now turn on the turbo switch which will

combine the 2kW setting with a 1kW fan boost setting to

give the total output of 3kw with fan boost.

Note that the fan and neon on the turbo switch will cycle

on and off under the control of the thermostat.

5.3 Timer Operation (device type DX 432Ti)

Set the slide switch (G) on the timer to:

Position 0: Heating Off

Position I: Manual Operation

This setting allows power to the heater uninter-

rupted by the timer settings. The heat selector

switch and thermostat will control the output (see

‘Controls’).

Position : Auto Operation

DO NOT disconnect this heater from the mains

supply unless it is being taken out of use (e.g. in

summer or for storage), otherwise the timer clock

will stop.

Setting the time of day

To set the time of day, rotate the timer dial clockwise

(indicated by the arrow) until the correct time of day is

opposite the reference mark. The 24-hour clock is

used; e.g. time shown for 4 pm is ‘16’ (16:00hrs).

Setting the Auto ON and OFF times

To set the timer:

1. Using your finger tip or the tip of a pencil, push in as

many segments as necessary around the dial,

according to the times you don’t require heat. Each

segment pushed in switches the heater OFF for that

part of the hour. All other segments will be ON. For

example, the above image shows the timer set to

switch the heater ON between 9.00am and 4.00pm and

between 9.30pm and 7.00am.

2. You can select as many ON periods as you like,

within the 24-hour day. The settings will repeat every

day until changed.

3. To change ON and OFF times, simply push in any

‘ON’ segments you wish to cancel and pull out new ‘ON’

segments as required.

Switching to Auto

Set the heat selector and

thermostat for the heat output

required. Check that the clock

shows the correct time of day.

Set the slide switch (G) to 

the heater will switch ON and

OFF according to the timer

settings.

6 Protection Against Overheating

If the permissible temperature is exceeded, the heating

device switches off automatically. If this occurs, pull the

mains plug out and leave the device unplugged for a

few minutes, so that the temperature limiter can switch

back again.

Then remove the cause e.g. when the air grid is

blocked or covered. When the device has cooled suffi-

ciently, it can be started up again.

7Faults

If the heating device does not give off heat, check the

following points:

Is the power switch (D) in the ON position?

Has the thermostat been set to the desired temper-

ature?

Has the overheat protection been triggered? See

section 6!

Is the fuse in the fuse box switched on?

If you cannot remedy the fault, please contact your

electrical retailer. To process your order, please state

the device type as well as its production number (E Nr.)

and manufacturing date (FD). This information is listed

on the type plate.

8Cleaning

To clean the device, first disconnect it from the mains

and allow it to cool down. Clean the outside of the unit

using a soft, damp cloth. Do not use scouring powder

or furniture polish as this may damage the surface.

21.30 pm - 16.00 pm

7.00 am - 9.00 am

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex DX431 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info