Bedienungsanleitung Dimplex HPL 12S-TURW (Seite 27 von 84) (Deutsch, Englisch, Französisch)

798232

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

www.glendimplex.de 452168.66.05a · FD 0104 EN-3

HPL 9S-TU(R)W - HPL 18S-TU(R)W English

2 Intended use of the heat

pump

2.1 Area of application

The air-to-water heat pump is intended exclusively for heating

or, depending on the device, also cooling heating water. It can

be used in new or existing heating systems.

The heat pump is suitable for mono energy and bivalent opera-

tion.

During continuous operation, proper defrosting of the evapora-

tor must be guaranteed by maintaining a heating water return

temperature of more than 18 °C.

The heat pump is not designed for the increased heat con-

sumption required when a building is being dried out. For this

reason, the additional heat consumption should be met using

special devices provided by the customer. For drying out a

building in autumn or winter, it is advisable to install a second

heat generator (e.g. an electric heating element available as an

accessory).

NOTE

ººººº

The device is not suitable for operation with a frequency

converter.

2.2 Operating principle

Heating

Surrounding air is drawn in by the fan and fed through the evap-

orator (heat exchanger). The evaporator cools the air, i.e. ex-

tracts heat from it. This extracted heat is then transferred to the

working medium (refrigerant) in the evaporator.

The heat is brought to a higher temperature level by increasing

its pressure with the aid of an electrically driven compressor. It

is then transferred to the heating water via the liquefier (heat

exchanger).

Electrical energy is used to raise the temperature of the heat

from the environment to a higher level. Because the energy ex-

tracted from the air is transferred to the heating water, this type

of device is referred to as an air-to-water heat pump.

The main components of an air-to-water heat pump are the

evaporator, fan and expansion valve, as well as the low-noise

compressor, liquefier and the electrical control system.

At low ambient temperatures, humidity accumulates on the

evaporator in the form of frost, reducing the transfer of heat.

Uneven accumulation during this process does not indicate a

fault. The evaporator is defrosted automatically by the heat

pump as required. Under certain atmospheric conditions,

steam may be emitted from the air outlet.

Cooling (device-dependent)

The functions of the evaporator and the liquefier are reversed in

the “Cooling” operating mode.

The heating water transfers its heat to the refrigerant via the liq-

uefier, which is now functioning as an evaporator. The refriger-

ant is brought to a higher temperature level using the compres-

sor. Heat is transferred to the surrounding air via the liquefier

(which, in heating operation, functions as an evaporator).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex HPL 12S-TURW Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info