Bedienungsanleitung Dimplex HPL 6S-TURW (Seite 19 von 60) (Deutsch, Englisch, Französisch)

798226

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

www.glendimplex.de 452163.66.68 · FD 0010 EN-3

HPL 6S-TU(R)W English

1.4 Energy-efficient use of the heat

pump

By operating this heat pump, you are helping to protect the en-

vironment. A prerequisite for energy-efficient operation is the

correct design of the heat source system and heating system.

It is particularly important for the efficiency of a heat pump to

keep the temperature difference between heating water and

heat source as small as possible. For this reason, it is advisable

to design the heat source and heating system very carefully. A

temperaturedifference of approximately one Kelvin (1 °C) in-

creases the power consumption by around 2.5 %. When de-

signing the heating system, it should be borne in mind that spe-

cial consumers such as domestic hot water preparation should

also be taken into consideration and dimensioned for low tem-

peratures. Underfloor heating systems (panel heating) are

optimally suited for heat pump use on account of the low flow

temperatures (30 °C to 40 °C).

It is important to ensure that the heat exchangers are not con-

taminated during operation, as this increases the temperature

difference, which in turn reduces the COP.

When set correctly, the heat pump manager is also an essential

factor in the energy-efficient use of the heat pump. Further in-

formation can be found in the heat pump manager operating

instructions.

2 Intended use of the heat

pump

2.1 Area of application

The air-to-water heat pump is intended exclusively for heating

or, depending on the device, also cooling heating water. It can

be used in new or existing heating systems.

The heat pump is suitable for mono energy and bivalent opera-

tion.

During continuous operation, proper defrosting of the evapora-

tor must be guaranteed by maintaining a heating water return

temperature of more than 18 °C.

The heat pump is not designed for the increased heat con-

sumption required when a building is being dried out. For this

reason, the additional heat consumption should be met using

special devices provided by the customer. For drying out a

building in autumn or winter, it is advisable to install a second

heat generator (e.g. an electric heating element available as an

accessory).

NOTE

The device is not suitable for operation with a frequency

converter.

2.2 Operating principle

Heating

Surrounding air is drawn in by the fan and fed through the evap-

orator (heat exchanger). The evaporator cools the air, i.e. ex-

tracts heat from it. This extracted heat is then transferred to the

working medium (refrigerant) in the evaporator.

The heat is brought to a higher temperature level by increasing

its pressure with the aid of an electrically driven compressor. It

is then transferred to the heating water via the liquefier (heat

exchanger).

Electrical energy is used to raise the temperature of the heat

from the environment to a higher level. Because the energy ex-

tracted from the air is transferred to the heating water, this type

of device is referred to as an air-to-water heat pump.

The main components of an air-to-water heat pump are the

evaporator, fan and expansion valve, as well as the low-noise

compressor, liquefier and the electrical control system.

At low ambient temperatures, humidity accumulates on the

evaporator in the form of frost, reducing the transfer of heat.

Uneven accumulation during this process does not indicate a

fault. The evaporator is defrosted automatically by the heat

pump as required. Under certain atmospheric conditions,

steam may be emitted from the air outlet.

Cooling (device-dependent)

The functions of the evaporator and the liquefier are reversed in

the “Cooling” operating mode.

The heating water transfers its heat to the refrigerant via the liq-

uefier, which is now functioning as an evaporator. The refriger-

ant is brought to a higher temperature level using the compres-

sor. Heat is transferred to the surrounding air via the liquefier

(which, in heating operation, functions as an evaporator).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex HPL 6S-TURW Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info