Bedienungsanleitung Dimplex LAK 14IMR (Seite 34 von 100) (Deutsch, Englisch, Französisch)

798322

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

EN-8 452162.66.09a · FD 0108 www.glendimplex.de

English LAK 3IMR - LAK 14ITR

6 Commissioning

6.1 General

To ensure that commissioning is performed correctly, it should

only be carried out by an after-sales service technician author-

ised by the manufacturer. This may be a condition for an addi-

tional warranty (see "Warranty service").

6.2 Preparation

The following items must be checked prior to commissioning:

All of the indoor unit connections must be installed as de-

scribed in Chapter 5.1.

All of the outdoor unit connections must be installed as de-

scribed in Chapter 7.

All valves which could impair the proper flow of the heating

water in the heating circuit must be open.

The air intake and air outlet paths must be clear.

The settings of the heat pump manager must be adapted

to the heating system in accordance with the manager's

operating instructions.

The heating water circuit must be completely filled and

purged.

Ensure that the condensate drain functions properly.

The outflow from the heating water pressure relief valve

must also function correctly.

Purging the heating system:

Ensure that all heating circuits are open, purge the system

at the highest position and refill water if necessary (comply

with static minimum pressure).

6.3 Commissioning procedure

The heat pump is commissioned via the heat pump manager.

Settings should be made in compliance with the HPM's instruc-

tions.

The heating element of mono energy systems should be dis-

connected during commissioning.

At heating water temperatures below 7 °C, commissioning is

not possible. The water in the buffer tank must be heated with

the 2nd heat generator to at least 18 °C.

The following procedure must then be followed to ensure prob-

lem-free commissioning:

1) Close all consumer circuits.

2) Ensure that the heat pump has the correct water flow.

3) Use the manager to select the automatic operating mode.

4) In the special functions menu, start the "Commissioning"

program.

5) Wait until a return temperature of at least 25 °C has been

reached.

6) Now slowly reopen the heating circuit valves in succession

so that the heating water flow rate is constantly raised by

slightly opening the respective heating circuit. The heat-

ing water temperature in the buffer tank must not be al-

lowed to drop below 20 °C during this process. This en-

sures that the heat pump can be defrosted at any time.

7) When all heating circuits are fully open and a return tem-

perature of at least 18 °C is maintained, the commissioning

is complete.

CAUTION!

Operating the heat pump at low system temperatures may

cause the heat pump to break down completely. After a

prolonged power failure, the commissioning procedure

detailed above must be followed.

Heat source

temperature Max. temperature spread

between heating flow and return

flow

by to

-20 °C -15 °C 4 K

-14 °C -10 °C 5 K

-9 °C -5 °C 6 K

-4 °C 0 °C 7 K

1 °C 5 °C 8 K

6 °C 10 °C 9 K

11 °C 15 °C 10 K

16 °C 20 °C 11 K

21 °C 25 °C 12 K

26 °C 30 °C 13 K

31 °C 35 °C 14 K

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LAK 14IMR Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info