Bedienungsanleitung Dimplex LAK 14ITR (Seite 32 von 100) (Deutsch, Englisch, Französisch)

798323

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

EN-6 452162.66.09a · FD 0108 www.glendimplex.de

English LAK 3IMR - LAK 14ITR

4.2 Precautions in winter and in

seasonal winds

In snowy areas or extremely cold locations, adequate pro-

tective measures must be taken to guarantee that the unit

continues functioning correctly.

Install the outdoor unit so that snow cannot fall directly on

the unit. If snow collects on the air inlet and freezes, errors

can occur. Install a cover in areas with snowfall.

When installing the outdoor unit in areas where there is a

lot of snowfall, ensure the unit is installed at least as high as

the level of an average snowfall (average annual snowfall).

If more than 100 mm of snow collects on the outdoor unit,

the snow must be removed prior to operation.

NOTE

ºººº

The intake and outlet opening of the outdoor unit should not

be positioned against the wind if possible.

5 Assembly indoor unit

5.1 General

The unit should always be installed indoors on a level, smooth

wall. Maintenance work can be carried out easily from the oper-

ator side (a minimum clearance at the side is not required). This

can be ensured by maintaining a clearance of 1 m at the front.

The indoor unit should be mounted at a height of approx.

1.30 m. It must be installed in a room protected from frost and

with short pipe runs.

NOTE

ººººº

Setup and installation must be performed by an authorised

specialist company.

When installing the indoor unit, the load-bearing capacity of the

wall should be checked. On account of the acoustics, measures

for isolating possible vibrations should also be very carefully

planned in advance.

The following connections need to be established on the indoor

unit:

Flow / return of the heating system

Safety valve outflow

Power supply

Supply voltage

Split refrigerant pipe

Condensate drain

Expansion vessel connection (optional)

NOTE

ºººº

When removing the unit cover, it must be taken into account

that the length of the connecting cable between the control

panel in the unit cover and the controller on the contact plate

is only 1.5 m. If the device cover can only be placed further

away than this when it has been removed, the plug

connection on the controller or on the control panel must first

be disconnected.

5.2 Indoor unit fixing

The indoor unit is attached to the wall with the screws and dow-

els (8 mm) included in the scope of supply. The following pro-

cedure should be used:

Mount the dowels for the top fastening eyelets.

Screw the screw into the dowel so that the indoor unit can

be mounted.

Mount the indoor unit by the upper fastening eyelets.

Mark the position of the side drill-holes.

Unhook the indoor unit again

Mount the dowels for the side drill holes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LAK 14ITR Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info