Bedienungsanleitung Dimplex LAK 14ITR (Seite 37 von 100) (Deutsch, Englisch, Französisch)

798323

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

www.glendimplex.de 452162.66.09a · FD 0108 EN-11

LAK 3IMR - LAK 14ITR English

Step 2: Fastening

Align the centre of the pipe and tighten the screw nuts by

hand.

Tighten the screw nuts with a spanner until they click.

Torques.

Step 3: Preventing foreign bodies from entering the

unit

Seal all pipe openings well with putty or a different type of

insulation (available separately).

If insects or small animals enter the outdoor unit, they can

cause short circuits in the control cabinet.

Lay the pipes. To do this, cover the coupling device of the

indoor unit with insulation and fix in place with two adhe-

sive tapes.

Adequate heat insulation is extremely important.

CAUTION!

Never open the valves of the outdoor component.

Carry out the work from Cap. 7.2 on pag. 11

and Cap. 7.3 on pag. 12 first of all.

7.2 Electrical connections

7.2.1 Outdoor unit

NOTE

ºººº

The DIP switches on the circuit boards in the outdoor unit

have no function. The positions of the DIP switches must

remain in their factory default and must not be changed!

Two cables must be connected on the outdoor unit:

A 'mains cable' and a 'data cable'

Both cables must be laid between the indoor and outdoor unit.

The mains cable is used to supply the outdoor unit with power

and the data cable is for communication between the outdoor

and indoor component. The VDE directives and regulations and

local conditions must be taken into account in the design and

installation of the two cables.

The indoor component already contains a safeguard element

for the outdoor component. The safeguarding of the entire heat

pump must also take place externally.

For LAK 3IMR, LAK 6IMR, LAK 9IMR, LAK 14IMR:

The mains cable on the outdoor unit must be three-core and

must be connected to the L / N / PE (power supply) terminals.

(See Cap. 3.2 on page XII; Cap. 3.5 on page XV and Cap. 3.8 on

page XVIII)

For LAK 14ITR

The mains cable on the outdoor unit must be 5-core and must

be connected to the R / S / T / N / PE terminals (see Cap. 3.5 on

page XV)

If no connection lugs are available, proceed as follows.

No cables with different thicknesses may be connected to

the connecting terminal. (one of the cables may come

loose during strong heat development.)

Multiple cables of the same thickness must be connected

as shown in the figure.

A shielded 2-core cable must be used as a data cable.

The data cable is connected to the terminals (Bus_A(+) /

Bus_B(-)) of the gateway circuit board (small circuit board in the

outdoor component) and to the heat pump manager (+/-) in the

indoor component (see Appendix, Connection diagram Chap.

2.5).

Outdoor unit

Continuously

Pipework of

the air side

Pipework of

the liquid side

Putty or insulation (available separately)

Drain hose

(if required)

Connection cable

Connection pipe

Round connection lugs Mains cable

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LAK 14ITR Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info