Bedienungsanleitung Dimplex LI 11MER (Seite 6 von 24) (Englisch)

520408

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

www.dimplex.de E-5

English

6.2

5Set-UP

5.1 General Information

The unit must be installed indoors on a level, smooth and hori-

zontal surface. The entire base of the frame should lie directly on

the floor to ensure a good soundproof seal. If this is not the case,

additional sound insulation measures may be necessary. If the

device is installed on top of a built-under buffer tank, a surface

that fully supports the base is required. The heat pump must be

installed so that maintenance work can be carried out without

being hindered. This can be ensured by maintaining a clearance

of 1 m in front and to the left and right of the heat pump.

Never install the device in rooms subject to high humidity. Con-

densation can form on the heat pump and air circuit if the humid-

ity exceeds 50% and the external temperature is below O °C.

If the heat pump is installed on an upper storey, the load-bearing

capacity of the ceiling should be checked. On account of the

acoustics, measures for isolating possible vibrations should also

be very carefully planned in advance as well. Installation on a

wooden floor is not recommended.

5.2 Condensed Water Pipe

Condensed water that forms during operation must be drained

off frost-free. The heat pump must be mounted on a level plane

to guarantee proper drainage. The condensed water pipe must

have a minimum diameter of 50 mm and should be fed frost-free

into a sewer. Condensate should not be discharged directly into

clearing tanks and cesspits because the aggressive vapours

could destroy the evaporator.

5.3 Sound

To prevent solid-borne sound from being transmitted to the heat-

ing system, we recommend connecting the heat pump to the

heating system using a flexible hose.

Installed air ducts should be sound-isolated from the heat pump

to prevent the transmission of solid-borne sound to the ducts.

6 Installation

6.1 General Information

The following connections need to be established on the heat

pump:

- Fresh and exhaust air

- Flow and return flow of the heating system

- Condensate outflow

- Power supply

6.2 Air Connection

ATTENTION!

Do not restrict or block the area around the air intake or outlet.

ATTENTION!

Only operate the heat pump with the air ducts connected.

The glass fibre reinforced concrete air ducts offered as accesso-

ries are moisture-resistant and diffusion-free.

The sealing collar is used to seal the air ducts on the heat pump.

The air ducts are not screwed directly onto the heat pump. Only

the rubber seal comes into direct contact with the heat pump

when the system is installed correctly. This guarantees easy as-

sembly and disassembly of the heat pump and also ensures that

solid-borne sound is well insulated.

If another type of air duct is used, observe the external and inter-

nal dimensions as specified in the figure. Also ensure that the vi-

bration and duct insulation are adequate.

If flange-mounted air ducts are used, connecting stubs are se-

cured on the air inlet and air outlet sides of the evaporator with 4

M8 x 16 hexagon bolts in the threaded holes provided. When

doing this, ensure that both air duct stubs only touch the insula-

tion. There should be no contact with the external sheeting.

P

P

 P

P

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LI 11MER Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex LI 11MER

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info