Bedienungsanleitung Dimplex LI 11TER plus (Seite 19 von 56) (Deutsch, Englisch, Französisch)

520411

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

www.dimplex.de EN-5

English

6.3

5 Transport

ATTENTION!

When transporting the heat pump, ensure that it is not tilted more than

45° (in any direction).

Use a wooden pallet for transporting the heat pump to the final in-

stallation location. The basic device can be transported with a lift

truck, hand truck or by means of 3/4" pipes fed through the holes

in the base plate or frame.

ATTENTION!

The heat pump and transport pallet are only joined by the packing film.

Before using the transport holes in the frame, it is necessary to

remove the lower side panel assemblies. This is done by loosen-

ing each of the two screws at the base and then withdrawing the

panels by unhooking them from above. Rehang the panels by

gently pushing them in an upwards direction.

Be careful not to damage any components when inserting the

pipes through the frame.

6Set-up

6.1 General Information

The unit must be installed indoors on a level, smooth and hori-

zontal surface. The entire base of the frame should lie directly on

the floor to ensure a good soundproof seal. If this is not the case,

additional sound insulation measures may be necessary. If the

device is installed on top of a built-under buffer tank, a surface

that fully supports the base is required. The heat pump must be

installed so that maintenance work can be carried out without

hindrance. This can be ensured by maintaining a clearance of

1 m in front and to the left and right of the heat pump.

Never install the device in rooms subject to high humidity. Con-

densation can form on the heat pump and air circuit if the humid-

ity exceeds 50 % and the external temperature is below O °C.

Neither frost nor temperatures higher than 35 °C must occur in

the installation location at any time of the year.

If the heat pump is installed on an upper storey, the load-bearing

capacity of the ceiling should be checked. On account of the

acoustics, measures for isolating possible vibrations should also

be very carefully planned in advance as well. Installation on a

wooden floor is not recommended.

6.2 Condensed Water Pipe

Condensate that forms during operation must be drained off

frost-free. To ensure proper drainage, the heat pump must be

mounted horizontally. The condensate pipe must have a mini-

mum diameter of 50 mm and must be fed into a sewer in such a

way that it is safe from frost. Do not discharge the condensate di-

rectly into clearing tanks or cesspits, as aggressive vapours or a

condensed water pipe which has not been laid in a frost-free

manner could destroy the evaporator.

6.3 Sound

To prevent solid-borne sound from being transmitted to the heat-

ing system, we recommend connecting the heat pump to the

heating system using a flexible hose. Connect the domestic

water circuit using the same type of connection.

Installed air ducts should be sound-isolated from the heat pump

to prevent the transmission of solid-borne sound to the ducts.

Opening the cover Closing the cover















P

P

 P

P

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LI 11TER plus Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex LI 11TER plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info