Bedienungsanleitung Dimplex LI 16I-TUR (Seite 30 von 72) (Deutsch, Englisch, Französisch)

798430

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

EN-8 452169.66.06 · FD 0009 www.glendimplex.de

English LI 16I-TUR

6Set-UP

6.1 General Information

The device is designed to enable several connection options.

The position of the air outlet opening can be moved from right

(factory default) to left or top by turning over one of the two

screwed on covers.

By replacing the bottom side cladding sections, it is also possi-

ble to move the hydraulic connection from left (factory default)

to right. The different connection options are shown in the di-

mension drawing(see cap. 1 on page II).

The air-to-water heat pump must be installed in a frost-free, dry

room on an even, smooth and horizontal surface. The entire

frame should lie directly on the floor to ensure an adequate

soundproof seal. If supporting feet are used, the heat pump

must be installed horizontally. In this case, the specified sound

level can be up to 3 dB(A) higher, and additional sound insula-

tion measures may be necessary.

The heat pump must be installed so that maintenance work can

be carried out without being hindered. This can be ensured by

maintaining a clearance of 1m in front of the heat pump and to

the side on which the heating water connections are located.

The side panel assemblies must not be covered by connecting

pipes.

Neither frost nor temperatures higher than 35 °C must occur in

the installation location at any time of the year.

Never install the device in rooms subject to high humidity. Con-

densation can form on the heat pump and air circuit if the hu-

midity exceeds 50 % and the external temperature is below

0°C.

If the heat pump is installed on an upper storey, the load-bear-

ing capacity of the ceiling should be checked. On account of

the acoustics, measures for isolating possible vibrations should

also be very carefully planned in advance as well. Installation on

a wooden floor is not recommended.

6.2 Condensed Water Pipe

Condensed water that forms during operation must be drained

off frost-free. To ensure proper drainage, the heat pump must

be mounted horizontally. The condensate pipe must have a

minimum diameter of 50 mm and must be fed into a sewer in

such a way that it is safe from frost. Do not discharge the con-

densate directly into clearing tanks or cesspits, as aggressive

vapours or a condensed water pipe which has not been laid in a

frost-free manner could destroy the evaporator.

6.3 Sound

We recommend connecting the heat pump to the heating

system using a flexible hose to prevent solid-borne noise

transmission to the heating system if requirements regard-

ing noise are high.

Installed air ducts should be sound-isolated from the heat

pump to prevent the transmission of solid-borne sound to

the ducts.

If the transport restraint screws are not removed from the

compressor, acoustic emissions from the device are signif-

icantly louder!

7 Installation

7.1 General Information

The following connections need to be established on the heat

pump:

- Fresh and exhaust air

- Flow and return flow of the heating system

- Condensate outflow

- Voltage supply

- Temperature sensor

1 m

(0,11 m)

0,1 m

0,11 m

(1 m)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LI 16I-TUR Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info