Bedienungsanleitung Dimplex LI 28TES (Seite 25 von 76) (Deutsch, Englisch, Französisch)

798318

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

www.gdts.one 452161.66.22 · FD 9912 EN-5

LI 20TES - LI 28TES English

4.3 Thermal energy meter WMZ

4.3.1 General description

The thermal energy meter (WMZ 25/32) is used for measuring

the quantity of thermal energy supplied. It is available as an ac-

cessory. Due to the additional heat exchanger, two thermal en-

ergy meters are required for measuring the quantity of thermal

energy.

Sensors in the flow and return of the heat exchanger pipes and

an electronics module acquire the measured values and trans-

mit a signal to the heat pump manager, which, depending on

the current operating mode of the heat pump (heating/DHW/

swimming pool), totals the thermal energy in kWh and displays

them in the operating data and history menu.

NOTE

The thermal energy meter complies with the quality

requirements of the German market incentive programme

subsidising efficient heat pumps. The thermal energy meter is

not subject to obligatory calibration, and can thus not be used

for the heating cost billing procedure!

4.3.2 Hydraulic and electrical integration of

the thermal energy meter

The thermal energy meter requires two measuring devices for

data acquisition.

A measuring tube for the flow measurement

This must be installed in the heat pump flow (observe flow

direction).

A temperature sensor (copper pipe with immersion sleeve)

This must be installed in the heat pump return.

The installation locations for both measuring tubes should be

as close to the heat pump as possible in the generator circuit.

To avoid eddying effects which could lead to incorrect meas-

urements, there should be a gap of 50 cm between the meas-

uring devices and other installed components such as pumps

or valves.

5 Transport

ATTENTION!

When transporting the heat pump, ensure that it is not tilted

more than 45° (in any direction).

Use a pallet for transporting the heat pump to the final installa-

tion location. The basic device can be transported with a lift

truck, hand truck or by means of 3/4" pipes fed through the

holes in the base plate or frame.

ATTENTION!

The heat pump and transport pallet are only joined by the

packing film.

Before using the transport holes in the frame, it is necessary to

remove the lower side panel assemblies. This is done by loosen-

ing each of the two screws at the base and then withdrawing

the panels by unhooking them from above. Rehang the panels

by gently pushing them in an upwards direction.

Be careful not to damage any components when inserting the

pipes through the frame.

After the transport, the transport securing device is to be re-

moved on either side at the bottom of the unit.

ATTENTION!

The transport securing device is to be removed prior to

commissioning.

Thermal energy meter casing - electronics

in the heating flow

in the heating return flow

Pulse, thermal energy meter

L / N / PE

230 V / 50 Hz

N1 / ID12

G/24 V AC

Opening the cover Closing the cover

Remove/screw in

transport lock

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex LI 28TES Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info