Bedienungsanleitung Dimplex Nissum concrete L (Seite 26 von 36) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

706573

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Maintenance

WARNING: ALWAYS UNPLUG BEFORE CARRYING OUT MAINTENANCE

Replacing the lamps

If a large amount of smoke looks grey or colourless, one or more lamps might be defective.

You can check defective lamps as follows:

1. While leaving the ame effect turned on, remove the fuel bed and water reservoir (see Figure 3) and remove the

adapter (see

Figure 4).

2. Look at the lamps from a distance in front of the re and determine which lamps should be replaced.

3. Put switch 'A' in the OFF (0) position (see Figure 2) and pull the plug out the wall socket.

4. Let the lamps cool off for 20 minutes before you remove them.

5. Remove the water reservoir by lifting it and place it in the kitchen sink.

6. Remove the receptacle as described in the chapter 'Cleaning'.

Maintenance

Control knob 'D': regulates the intensity of the ame and the smoke effect when the re is turned on.

Turning the control knob towards you reduces the intensity of the ame and the smoke effect. Turning the

control knob away from you increases the intensity of the ame and the smoke effect.

If the water reservoir is empty, the main lamps will turn off. See the instruction in 'Maintenance', 'Filling the water

reservoir'. When this procedure is completed, the main lamps will turn on, but it takes another 30 seconds before the

ames will turn on again.

Setting the thermostat

Insert the plug in the wall socket and put the re in the highest heating position. Turn the control knob 'C' completely

away from you (maximum temperature setting) to heat the room quickly. Once the room has reached the desired

temperature, you tun the thermostat knob slowly towards you until you hear a click. This indicates that the thermostat

has turned off. The thermostat of the re ensures that the room temperature stays at the selected level.

Note: If your re does not re up with the thermostat on a low setting, the room temperature might be higher than the

thermostat setting.

Thermal safeguard

A limiting mechanism is built in the fan heater as a thermal safeguard to prevent damage caused by overheating. This

can occur if the heat exhaust is blocked in any way. If the limiting mechanism starts to operate, you must pull the plug

of the re out the wall socket. Wait approx. 10 minutes before you re-insert the plug. However, prior to turning on the

re, you must remove the obstacles that block the heat exhaust.

Caution: To prevent re hazard caused by unintentional setting of the thermal safeguard, the apparatus may not be

supplied with power via an external switch (timer, etc.).

Tips for using the re

1. The Opti-myst ame and smoke eect will last for approximately 9hrs when the product is turned to full ame, and

approximately 12hrs when set at minimum. These times are a guideline only and can vary.

2. Do not tilt or move the re when there is water in the water reservoir or receptacle.

3. Make sure that the stove is attached spirit level to the wall.

4. The ame control knob ‘D’ (Figure 2) can be turned higher or lower for a more realistic effect.

5. Sometimes the ames look more natural if the ame control knob is turned to a low setting.

6. Give the ame mechanism some time to respond to the changes that you make with the ame control knob.

Using the remote control

On the control panel, the switch ‘A’ (see Figure 2) must be set to the ON ( I ) position so that the remote control functions.

The remote control has three buttons (see Figure 7). The remote control should point to the heat exhaust in order to

function properly (see Figure 12). The remote functions are as follows:

Push this button once to turn on the ame effect.

This is indicated by a single beep.

Push this button to get the ame effect and heating on 50% capacity.

This is indicated by two beeps.

Push this button again to get the ame effect and heating on maximum capacity.

This is indicated by three beeps.

Standby

This is indicated by a single beep.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Nissum concrete L Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info