when the room is warm. T
knob clockwise until the required setting is reached.
cold room quickly
reached the desired temperature, turn the thermostat knob anti-clockwise
until the thermostat just clicks off.
at this temperature.
The thermostat also has a frost protection setting marked ‘ ’. This setting is
useful in areas such as garages, to prevent frost damage. If the thermostat
is set to its minimum setting ‘ ’, the heater will cycle on and off to maintain
a temperature of approximately 5° to help protect against frost.
Note: Should the heater fail to come on when the thermostat is at a low
setting, this may be due to the room temperature being higher than the
thermostat setting.
Heat Selector Switches (see Fig.5)
Selector switches located on the control panel provide a choice of heat output
to suit varying conditions and for economy of operation.
T
Model Switch Switch
OFC1200/OFC1200TI 650W 1200W
OFC1500/OFC1500TI/OFC1500TIF 800W 1500W
OFC2000/OFC2000TI 1 2000W
OFC2400/OFC2400TI/OFC2400TIF 1200W 2400W
Fan Heater (see Fig.6)
T
switched on.
Digital Timer Operation (see Fig.7)
MPORT Remember to observe all safety warnings when operating the
heater on auto setting, either attended or unattended.
The timer allows you to select ‘AUTO ’MAN ON ’ by pressing the ‘MODE’
button until the required MODE appears at the bottom of the timer display
‘MAN OFF’
‘MAN ON’
settings.
‘AUTO DL
daily program.
‘AUTO
for weekdays only or weekends only
Initial Operation
Note: Timer Memory Back Up Batteries – Once the heater has been left
plugged in with the socket switched on for at least 72 hours the timer
memory back up batteries will be fully charged.
In the event of a power cut or disconnection from the mains, the timer
will continue to function and all programmed settings will be retained
for up to six months providing the timer batteries are fully charged.
If however the timer batteries have not been charged fully
heater is deprived of power for longer than six months, then the time
and programme settings are likely to be lost and you may therefore need
to reset the time and programme before using the ‘AUTO’.
For initial use, plug the heater into a regular household power point and turn
the power on. The timer is now ready to be set up for use.
Setting Time
1. Press the ‘PROGRAM ’ appears on the
top left hand side of the screen. The user can now set the clock.
2. - ‘ & ‘+ ’
the hour digit by pressing ‘ENTER ’.
3. Once ‘ENTER’ has the ash. T adjust
minutes ENTER’.
4. The timer now returns to the default display
5. T
Once the correct time is set, a total of four ON/OFF time programs can be
set for operation.
Setting Programmes
OPTION 1; Daily ( ‘DL on display): This is a daily program function, Monday
to Sunday with four ON/OFF program options available.
OPTION 2; ‘BLK’ on display): This is a block program function, Monday
to Friday with four ON/OFF program options or Saturday to Sunday with four
ON/OFF program options.
Press the ‘PROGRAM’ key twice to set the programs starting with ‘Daily
ON’ P1.
Setting P1 On Time
1. T- ’ & +’
ENTER.
2. T- ’ & +’ buttons.
pressing ENTER.
Note: The minutes can only be set in 10 minute blocks.
Setting P1 Off Time
3. T- ’ & +’
ENTER.
4. T- ’ & +’
pressing ENTER.
Repeat steps 1 to 4 to programme P2, P3 and P4 . After P4
you automatically enter the BLOCK programme option. Repeat steps 1 to 4
to programme P2, P3 and P4 . P4 you automatically exit
the BLOCK programme option.
At any time while programming the timer you can press the PROGRAM button
to exit to the default display
NOTE: Y
the MODE button.
The Advance
When in + ’
the programme will
only revert back to the program when the subsequent programme time is
reached. When the ADVfunction is running the ADVsegment
will be displayed on the LCD screen. If the ‘- ‘ button is pressed for longer
than 2 seconds when the ADVprogramme is running the ADV
feature will automatically be cancelled and the programme will run as normal.
e.g. If the present time is 14:00 and P1 ON is at 17:00 and P1 OFF is 19:00,
if ‘+ ’ADVdisappears
from the screen at 17:00 as set program is then running.
Key Lock
T
will appear on the screen when the keypad is locked. T
repeat the action above.
Safety in use
This appliance incorporates a number of safety devices. In addition to the
‘Important section your attention is drawn to the following;
Tilt Switch
The tilt switch will prevent the heater from working if it is accidentally tipped
over on its side. If the radiator is tipped over while it is hot, disconnect the
power and allow it to cool, then stand the radiator back upright. Reconnect
the power - normal operation should be resumed.
Safety Overheat Protection
The
should it overheat for any reason. If the cut-out operates it is the result of
abnormal overheating, and customer services should be contacted for further
advice - see ‘After Sales Service’ .
Storage
If the radiator is not required for long periods, for example during the summer
it should be stored in a dry place and preferably covered to prevent the
accumulation of dirt and dust. The supply cord should be neatly coiled around
the cable wrap (see Fig. 1 ) and the plug should be inserted in to the plug pin
holes provided in the cable wrap.
IMPORT
Prolonged storage/mains disconnection periods may cause the timer to lose its
programmed settings and may require reprogramming, see initial operation
Cleaning
W
CLEANING THE HEA
Do not use detergents, abrasive cleaning powder or polish of any kind on the
body of the heater
dust
moisture in to the heater
Recycling
For electrical products sold within the European Community
end of the electrical products useful life it should not be disposed
of with household waste. Please recycle where facilities exist.
Check with your Local
in your country
After Sales Service
Should you require after sales service or should you need to purchase any
spares, please contact the retailer from whom the appliance was purchased.
Please
result in loss or damage and delay in providing you with a satisfactory service.
The ns
requiring opening of the oil container are only to be made by the manufacturer
or its service agent. For further advice if an oil leak is suspected please contact
the retailer from whom the appliance was purchased. Regulations concerning
the disposal of oil when scrapping the appliance must be followed. Please
retain your receipt as proof of purchase.
