Bedienungsanleitung Dimplex SI 14TE (Seite 25 von 64) (Deutsch, Englisch, Französisch)

520420

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

www.dimplex.de EN-9

English

9.3

ATTENTION!

Ensure that there is a clockwise rotating field: Operating the compressor

in the wrong rotational direction may cause damage to the compressor.

The correct control voltage must be ensured according to the de-

vice information and/or the type plate.

For detailed information, refer to the appendix.

8.3 Thermal energy meter WMZ

8.3.1 General description

The thermal energy meter (WMZ 25/32) is used for measuring

the quantity of thermal energy supplied. It is available as an ac-

cessory. Due to the additional heat exchanger, two thermal en-

ergy meters are required for measuring the quantity of thermal

energy.

Sensors in the flow and return of the heat exchanger pipes and

an electronics module acquire the measured values and transmit

a signal to the heat pump manager, which, depending on the cur-

rent operating mode of the heat pump (heating/DHW/swimming

pool), totals the thermal energy in kWh and displays them in the

operating data and history menu.

NOTE

The thermal energy meter complies with the quality requirements of the

German market incentive programme subsidising efficient heat pumps.

The thermal energy meter is not subject to obligatory calibration, and can

thus not be used for the heating cost billing procedure!

8.3.2 Hydraulic and electrical

integration of the thermal

energy meter

The thermal energy meter requires two measuring devices for

data acquisition.

A measuring tube for the flow measurement

This must be installed in the heat pump flow (observe flow

direction).

A temperature sensor (copper pipe with immersion sleeve)

This must be installed in the heat pump return.

The installation locations for both measuring tubes should be as

close to the heat pump as possible in the generator circuit.

To avoid eddying effects which could lead to incorrect measure-

ments, there should be a gap of 50 cm between the measuring

devices and other installed components such as pumps or

valves.

Fig. 8.7:Hydraulic and electrical components of the thermal ener-

gy meter

9 Commissioning

9.1 General Information

To ensure that start-up is performed correctly, it should only be

carried out by an after-sales service technician authorised by the

manufacturer. This may be a condition for extending the guaran-

tee (see Warranty).

9.2 Preparation

The following items need to be checked prior to start-up:

The heat pump must be fully connected, as described in

Chapter 7.

The heat source system and the heating circuit must have

been filled and checked.

The dirt trap must be inserted in the brine inlet of the heat

pump.

All valves that could impair proper flow in the brine and heat-

ing circuits must be open.

The heat pump manager must be adapted to the heating

system in accordance with the controller’s operating instruc-

tions.

9.3 Start-up Procedure

The heat pump is started up via the heat pump manager.

ATTENTION!

The heat pump must be started up in accordance with the installation and

operating instructions of the heat pump manager.

If an overflow valve is fitted to assure the minimum heating water

flow rate, the valve must be set in accordance with the require-

ments of the respective heating system. Incorrect adjustment

can lead to faulty operation and increased energy consumption.

We recommend carrying out the following procedure to correctly

adjust the overflow valve:

Close all of the heating circuits that may also be closed during

operation (depending on the type of heat pump usage) so that

the most unfavourable operating state - with respect to the water

flow rate - is achieved. This normally means the heating circuits

of the rooms on the south and west sides of the building. At least

one heating circuit must remain open (e.g. bathroom).

The overflow valve should be opened far enough to produce the

maximum temperature spread between the heating flow and re-

turn flow listed in the table below for the current heat source tem-

perature. The temperature spread should be measured as close

as possible to the heat pump. The heating element of mono en-

ergy systems should be disconnected.

/13(

9+]

1,'

*9$&

7KHUPDOHQHUJ\PHWHUFDVLQJHOHFWURQLFV

LQWKHKHDWLQJIORZ

LQWKHKHDWLQJUHWXUQIORZ

3XOVHWKHUPDOHQHUJ\PHWHU

Heat source

temperature

Max. temperature spread

between heating flow and return

flow

From To

-5° C 0° C 10 K

1° C 5° C 11 K

6° C 9° C 12 K

10° C 14° C 13 K

15° C 20° C 14 K

21° C 25° C 15 K

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SI 14TE Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex SI 14TE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info