Bedienungsanleitung Dimplex SI 35TU (Seite 19 von 68) (Deutsch, Englisch, Französisch)

798242

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

www.glendimplex.de 452237.66.48a · FD 0108 EN-3

SI 26TU - SI 35TU English

3Basic device

The basic device consists of a heat pump for indoor installation

wired ready for use with metal casing, switch box and inte-

grated heat pump manager. The refrigeration circuit is "hermet-

ically sealed" and contains the fluorinated refrigerant R410A in-

cluded in the Kyoto protocol. Information on the GWP value

and CO2 equivalent of the refrigerant can be found in the chap-

ter Device information. The refrigerant is CFC-free, non-ozone

depleting and non-combustible.

All components required for the operation of the heat pump are

located in the switch box. An outside temperature sensor in-

cluding fixing accessories and a dirt trap are supplied with the

heat pump. The supply for the supply voltage and the control

voltage must be installed by the customer.

The circulating pumps (brine and heating water side) included

in the scope of supply must be installed in accordance with the

hydraulic diagrams (see Cap. 4 on page XX) or the development

documents. The electrical connection of the circulating pumps

must be established in accordance with Cap. 7.5.3 on page 8.

The customer must provide both the heat source system and

the brine circuit manifold.

1) Switch box

2) Evaporator

3) Liquefier

4) Filter dryer

5) Compressor 1

6) Compressor 2

7) Expansion valve

8) Economiser

4 Accessories

4.1 Connection flange

The device can optionally be switched to flange connection

using the flat-sealing connection flange.

4.2 Remote control

A remote display adds convenience and is available as a special

accessory. Operation and menu navigation are identical to

those of the heat pump manager. Connection takes place via an

interface (special accessories) with RJ 12 Western plug.

NOTE

ºººº

In the case of heating controllers with a removable control

panel, this can also be used directly as a remote display.

4.3 Building management system

The heat pump manager can be connected to a building man-

agement system network via supplementation of the relevant

interface plug-in card. The supplementary installation instruc-

tions of the interface card must be consulted regarding the

exact connection and parameterisation of the interface.

The following network connections can be made on the heat

pump manager:

Modbus

EIB, KNX

Ethernet

CAUTION!

If the heat pump or circulating pumps are controlled

externally, a flow rate switch is required to prevent the

compressor from being switched on when there is no volume

flow.

5 Transport

A lift truck is suited for transporting the unit on a level surface.

Carrying straps may be used if the heat pump needs to be

trans-ported on an uneven surface or carried up or down stairs.

These straps can be passed directly underneath the pallet.

CAUTION!

The heat pump must not be tilted more than 45° (in any

direction).

Use the holes provided in the sides of the frame to lift the unit

without the pallet. The side panel assemblies must be removed

for this purpose. Any commercially available length of pipe can

be used as a carrying aid.

45°

max.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SI 35TU Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info