Bedienungsanleitung Dimplex SI 70CS (Seite 15 von 56) (Deutsch, Englisch, Französisch)

798488

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

www.dimplex.de E-3

English

3.2

2 Purpose of the Heat

Pump

2.1 Application

The brine-to-water heat pump is to be used exclusively for the

heating of heating water. It can be used in new or previously ex-

isting heating systems. Brine is used as the heat transfer medium

in the heat source system. Borehole heat exchangers, ground

heat collectors or similar systems can be used as the heat

source.

2.2 Operating Principle

The heat generated by the sun, wind and rain is stored in the

ground. This heat stored in the ground is collected at a low tem-

perature by the brine circulating in the ground collector, ground

coil or similar device.

A circulating pump then conveys the “heated” brine to the evap-

orator of the heat pump. There the heat is given off to the refrig-

erant in the refrigerating cycle. This cools the brine so that it can

once again absorb thermal energy in the brine circuit.

The refrigerant is drawn in by the electrically driven compressor,

compressed and “pumped” to a higher temperature level. The

electrical power needed to run the compressor is not lost in this

process. Most of it is absorbed by the refrigerant.

Subsequently, the refrigerant is passed through the condenser

where it transfers its heat energy to the heating water. Depend-

ing on the set operating point (thermostat setting), the heating

water can thus be heated up to a max. of 60 °C.

3 Scope of Delivery

3.1 Basic Device

The basic device consists of a ready-to-use heat pump for indoor

installation, complete with cover and basic control. The refriger-

ant circuit is hermetically sealed. It contains the Kyoto protocol

approved refrigerant R407C with a GWP value of 1525. It is

CFC-free, does not deplete ozone and is non-flammable. The

cover is lined with a sound insulation.

All components required for the operation of the heat pump are

located in the basic control. The load feed and the control line

(accessories) between the heat pump and the basic control must

be installed by the customer.

The brine pump provided by the customer must be connected to

the basic control. It must be equipped with a motor protection de-

vice, if applicable.

The customer must provide both the collector and the brine cir-

cuit manifold.

1) Connection box

2) Compressor

3) Evaporator

4) Liquifier

5) Filter dryer

ATTENTION!

The cover cannot be painted.

3.2 Heat Pump Controller

The use of a heat pump controller from our product range is

absolutely essential for brine-to-water heat pump operation.

The heat pump controller is a convenient electronic regulation

and control device. It controls and monitors the entire heating

system on the basis of the external temperature, including do-

mestic hot water preparation and safety systems. The operating

instructions included in the scope of supply of the heat pump

controller describe its function and use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SI 70CS Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info