Bedienungsanleitung Dimplex SI 70CS (Seite 18 von 56) (Deutsch, Englisch, Französisch)

798488

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

E-6

English

Control voltage

The basic control is supplied with power via the control line. A

separate line to the basic control is not required.

Power connection between the basic control and the connection

box of the heat pump

The connections between the terminal box in the heat pump and

the basic control as well as between the brine pump and the

basic control must be carried out on site.

The cross sections for the power cables are to be selected ac-

cording to the power consumption of the heat pump (technical

data) as well as according to the power consumption of the in-

stalled brine circulating pump.

The power cables are routed through the installed plastic pipe.

Connection terminals for the compressor:

X1-1/2/3/PE

X1-4/5/6/PE

Connection terminals, brine circulating pump:

X1-7/8/9/PE

Control connection between the basic control and

the connection box of the heat pump

The control connection between the connection box of the heat

pump and the basic control is provided by a ready-for-use control

line (see price list). The control line is laid with the round 16-pole

plug connector from the basic control to the connection box of the

heat pump. The anti-twist mechanism of the plug connector can

be located by gently pushing in the control line while at the same

time carefully turning it to the left or right. The plug connector

must then be interlocked until the lifting eye nut locks with the

plug connector. The plug connection is established and secured

by turning the lifting eye nut to the right. The two rectangular plug

connectors are guided through the feed on the lower right-hand

side of the basic control and are (non-interchangeably) con-

nected with their counterparts. The control cable must be se-

cured with the strain relief in the basic control. Slack parts of the

control cable can remain in a cable duct or be looped on the wall.

Connecting the heat pump controller to the basic

control (with a 1.5-m control line, see price list)

The round plug connectors are used to connect the control line to

the basic control and the rectangular plug connectors are used to

connect it to the heat pump controller. More detailed information

can be found in the installation and operating instructions of the

heat pump controller.

ATTENTION!

Observe that the rotary field rotates in a clockwise direction when

connecting the mains cables. (If the rotary field is not clockwise, the heat

pump will not work properly and will be very noisy).

8 Start-up

8.1 General Information

To ensure that start-up is performed correctly, it should only be

carried out by an after-sales service technician authorised by the

manufacturer. This may be a condition for extending the guaran-

tee (see Warranty).

8.2 Preparation

The following items need to be checked prior to start-up:

The heat pump must be fully connected, as described in

Chapter 7.

The heat source system and the heating circuit must have

been filled and checked.

The dirt trap must be inserted in the brine inlet of the heat

pump.

All valves that could impair proper flow in the brine and heat-

ing circuits must be open.

The heat pump controller must be adapted to the heating

system in accordance with the controller’s operating instruc-

tions.

8.3 Start-up Procedure

The heat pump is started up via the heat pump controller.

ATTENTION!

Start-up must be performed in accordance with the installation and

operating instructions of the heat pump controller.

If an overflow valve is fitted to assure the minimum heating water

flow rate, the valve must be set in accordance with the require-

ments of the respective heating system. Incorrect adjustment

can lead to faulty operation and increased energy consumption.

We recommend carrying out the following procedure to correctly

adjust the overflow valve:

Close all of the heating circuits that may also be closed during

operation so that the most unfavourable operating state - with re-

spect to the water flow rate - is achieved. This normally means

the heating circuits of the rooms on the south and west sides of

the building. At least one heating circuit must remain open (e.g.

bathroom).

The overflow valve should be opened far enough to produce the

maximum temperature spread between the heating flow and re-

turn flow listed in the table below for the current heat source tem-

perature. The temperature spread should be measured as close

as possible to the heat pump. The heating element of mono en-

ergy systems should be disconnected.

Any faults occurring during operation are displayed on the heat

pump controller and can be corrected as described in the operat-

ing manual of the heat pump controller.

Heat source

temperature

Max. temperature spread

between heating flow and

return flow

From To

-5° C 0° C 10 K

1° C 5° C 11 K

6° C 9° C 12 K

10° C 14° C 13 K

15° C 20° C 14 K

21° C 25° C 15 K

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SI 70CS Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info