Bedienungsanleitung Dimplex SI 75TE (Seite 17 von 72) (Deutsch, Englisch, Französisch)

798448

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.dimplex.de 452234.66.02 · FD 9311 EN3

English

SI 50TE - SI 130TE

1.4 Energy-Efficient Use of the

Heat Pump

By operating this heat pump you contribute to the protection of

our environment. A prerequisite for an efficient operation is the

proper design and sizing of the heating system and the heat

source system. In particular, it is important to keep water flow

temperatures as low as possible. All energy consumers con-

nected should therefore be suitable for low flow temperatures. A

1 K higher heating water temperature corresponds to an in-

crease in power consumption of approx. 2.5 %. Low-temperature

heating systems with flow temperatures between 30 °C and

50 °C are optimally suited for energy-efficient operation.

2 Purpose of the heat

pump

2.1 Application

The brine-to-water heat pump is to be used exclusively for the

heating and cooling of heating water. It can be used in new or

previously existing heating systems. The mixture of water and

frost protection (brine) acts as a heat transfer medium in the heat

source system. Ground probes, ground heat collectors or similar

systems can be used as heat source systems.

2.2 Principle of Operation

The heat generated by the sun, wind and rain is stored in the

ground. This heat stored in the ground is collected at low temper-

ature by the brine circulating in the ground collector, ground coil

or similar device.

A circulating pump then conveys the warmed brine to the evapo-

rator of the heat pump. There, the heat is given off to the refrig-

erant in the refrigeration cycle. When so doing, the brine cools so

that it can again take up heat energy in the brine circuit.

The refrigerant is drawn in by the electrically driven compressor,

is compressed and “pumped” to a higher temperature level. The

electrical power needed to run the compressor is not lost in this

process, but most of the generated heat is transferred to the re-

frigerant.

Subsequently, the refrigerant is passed through the condenser

where it transfers its heat energy to the heating water. Based on

the thermostat setting, the heating water is thus heated to up to

58 °C.

3 Basic device

The device consists of a heat pump for indoor installation wired

ready for use with metal casing, switch box and integrated heat

pump manager. The refrigerant circuit contains the Kyoto proto-

col approved refrigerant R404A with a GWP value of 3784. It is

CFC-free, does not deplete ozone and is non-flammable.

All components required for the operation of the heat pump are

located in the control box. A sensor for the externall temperature

including mounting hardware as well as a strainer are supplied

with the heat pump. The supply for the load current and the con-

trol voltage must be installed by the customer.

The control wire of the brine pump (to be provided by the cus-

tomer) is to be connected to the control box. When so doing, a

motor protecting device is to be installed, if required.

The customer must provide both the heat source system and the

brine circuit manifold.

1) Control

2) Evaporator

3) Condenser

4) Compressor

5) Transport securing devices

6) Filter drier







Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SI 75TE Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info