Bedienungsanleitung Dimplex SI 7ME (Seite 23 von 56) (Deutsch, Englisch, Französisch)

798212

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

www.dimplex.de 452232.66.13 · FD 9603 EN-9

English

SI 5ME - SI 14ME

8 Commissioning

8.1 General Information

To ensure that start-up is performed correctly, it should only be

carried out by an after-sales service technician authorised by the

manufacturer. These measures can also include an additional

warranty under certain conditions (see Warranty).

8.2 Preparation

The following items need to be checked prior to start-up:

The heat pump must be fully connected, as described in

Chapter 7.

The heat source system and the heating circuit must have

been filled and checked.

The dirt trap must be inserted in the brine inlet of the heat

pump.

All valves that could impair proper flow in the brine and heat-

ing circuits must be open.

The heat pump manager must be adapted to the heating

system in accordance with the controller’s operating instruc-

tions.

8.3 Start-up Procedure

The heat pump is started up via the heat pump manager.

ATTENTION!

The heat pump must be started up in accordance with the installation and

operating instructions of the heat pump manager.

If an overflow valve is fitted to assure the minimum heating water

flow rate, the valve must be set in accordance with the require-

ments of the respective heating system. Incorrect adjustment

can lead to faulty operation and increased energy consumption.

We recommend carrying out the following procedure to correctly

adjust the overflow valve:

Close all of the heating circuits that may also be closed during

operation (depending on the type of heat pump usage) so that

the most unfavourable operating state - with respect to the water

flow rate - is achieved. This normally means the heating circuits

of the rooms on the south and west sides of the building. At least

one heating circuit must remain open (e.g. bathroom).

The overflow valve should be opened far enough to produce the

maximum temperature spread between the heating flow and re-

turn flow listed in the table below for the current heat source tem-

perature. The temperature spread should be measured as close

as possible to the heat pump. The heating element of mono en-

ergy systems should be disconnected during start-up.

9 Maintenance and

Cleaning

9.1 Maintenance

To prevent faults due to sediment in the heat exchangers, care

must be taken to ensure that no impurities can enter either the

heat source system or the heating system. In the event that op-

erating malfunctions due to contamination occur nevertheless,

the system should be cleaned as described below.

9.2 Cleaning the Heating System

The ingress of oxygen into the heating water circuit may result in

the formation of oxidation products (rust), particularly if steel

components are used. This oxygen enters the heating system via

the valves, the circulating pumps and/or plastic pipes. It is there-

fore essential - in particular with respect to the piping of under-

floor heating systems - that only diffusion-proof materials are

used.

NOTE

We recommend the installation of a suitable corrosion protection system

to prevent the formation of deposits (e.g. rust) in the condenser of the

heat pump.

Residue from lubricants and sealants may also contaminate the

heating water.

In the case of severe contamination leading to a reduction in the

performance of the liquifier in the heat pump, the system must be

cleaned by a heating technician.

Based on current knowledge, we recommend carrying out the

cleaning with a 5 % phosphor acid or, if more frequent cleaning

is required, with a 5 % formic acid.

In either case, the cleaning fluid should be at room temperature.

We recommend flushing the heat exchanger in the direction op-

posite to the normal flow direction.

To prevent acidic cleaning agents from entering the heating sys-

tem circuit, we recommend connecting the flushing device di-

rectly to the flow and return flow of the liquifier. It is important that

the system be thoroughly flushed using appropriate neutralising

agents to prevent any damage from being caused by cleaning

agent residue remaining in the system.

Acids must be used with great care and all relevant regulations of

the employers’ liability insurance associations must be adhered

to.

The manufacturer's instructions regarding cleaning agent must

be complied with at all times.

9.3 Cleaning the Heat Source

System

NOTE

The supplied dirt trap must be inserted in the heat source inlet of the heat

pump to protect the evaporator against the ingress of impurities.

The filter sieve of the dirt trap should be cleaned one day after-

start- up. Further checks must be set according to the level of

dirt.If no more signs of contamination are evident, the filter can

be removed to reduce pressure drops.

Heat source

temperature

Max. temperature spread

between heating flow and return

flow

From To

-5 °C 0 °C 10 K

1°C 5°C 11 K

6 °C 9 °C 12 K

10 °C 14 °C 13 K

15 °C 20 °C 14 K

21 °C 25 °C 15 K

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SI 7ME Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex SI 7ME

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info