Bedienungsanleitung Dimplex SRX 070C (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Polnisch, Türkisch, Norwegisch, Finnisch)

520437

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

- 2 -

Hydraulic connection

To ensure a sufficient water flow rate through the fan convec-

tors, observe the following points:

- The devices are not suitable for installation in single-pipe

systems.

- The nominal width of the connection pipe must have a

minimum diameter of 15 mm.

- If the devices are installed in a heating system with various

heat distribution systems (e.g. underfloor heating), a sepa-

rate circuit is required to guarantee a sufficient water flow

rate.

- For optimum operation (heat output) of the fan convectors,

a hydraulic balance is required on the heating system.

Fig. 5 shows the various hydraulic connection options on the

device. The recommended flow and return connections are

shown in fig. 5 and fig. 4. The heating pipes can be laid in the

floor or in the wall. The device is supplied with two copper pipes

with a diameter of 15 mm that are fitted on the heat exchanger

at the factory.

Before and during filling of the heating system, all pipe connec-

tions must be checked for leaks. During filling, the bleeder valve

(see fig. 4) must be open such that air can escape from the de-

vice. If necessary, bleed again following commissioning (circulat-

ing pump running).

Connect the condensate pipe supplied to the outlet nozzle and

route to a suitable outlet with a gradient of at least 5°.

Electrical connection

WARNING – The device must be grounded!

WARNING – Phase conductor (brown) and neutral conductor

(blue) must not be swapped as this may cause malfunctions.

The electrical connection should have a supply voltage of ~230-

240V, 50 Hz.

The device must be installed by a qualified electrician in compli-

ance with the existing standards and local installation guide-

lines.

Before performing installation, ensure that the power supply is

switched off.

The device is equipped with a flexible 1 m connection cable (4 x

0.75 mm²), which can be used to connect the heater directly to

the power supply via a suitable wall socket.

In the electrical supply line, fit a circuit breaker for each pole

with a contact opening width of at least 3 mm. Automatic fuses

are also permitted as separators. Automatic fuses should have a

delayed tripping characteristic.

Conductor configuration of the connection cable:

Brown: 'L' – supply voltage phase conductor

Blue: 'N' – supply voltage neutral conductor

Green/yellow: 'PE' – grounding conductor

Black: control conductor (temperature reduction; on/off)

For circuit diagram, see fig. 6.1 resp. fig. 6.2.

Control conductor

By activating the control conductor, see fig. 6.1, the set tem-

perature on the device is lowered or raised depending on the

selected mode.

See also "Changing automatically the set temperature"

The temperature change is forwarded to any downstream de-

vices via the control conductor.

If a programming cassette is used, the control signal from the

cassette, which is plugged into the pilot device, is forwarded to

any downstream devices; see fig. 6.2.

The control conductor does not have to be in phase with the

supply connection. If the control conductor is not used, it must

be properly insulated.

WARNING – if you switch over to controlled operation, the

mains voltage is on this conductor!

WARNING – do not ground the control conductor.

When taking out of service, e.g. for maintenance work, ensure

that both the mains supply and the control conductor are dis-

connected from the power supply, because this may result in

external voltage (via a timer contact or pilot device with pro-

gramming cassette).

Final installation

Fit casing cover following completion of installation work. To do

this, screw in the four fixing screws on the underside of the de-

vice, see fig. 2.

Operation

The control panel is shown in fig. 3.

The individual elements have the following meaning:

A – Operating mode button

B – On/off indicator

C – Cooling mode indicator

D – Heating mode indicator

E – Fan level button

F – Low fan level indicator

G – Medium fan level indicator

H – High fan level indicator

J – Thermostat setting wheel

K – Cover for programming cassette slot

Heating mode

Press the button once or several times until the red in-

dicator lights up.

Set the desired room temperature with the setting wheel.

Depending on the current room temperature and the tem-

perature set on the thermostat, the electronics calculate

which fan level (fan speed) to use.

There are 3 possible fan levels. If necessary, the number of pos-

sible fan levels can be reduced. For instance, to limit the fan

levels to a maximum of 2, press the button once or sev-

eral times until the red 2 indicator lights up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex SRX 070C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info