Bedienungsanleitung Dimplex stockbridge (Seite 3 von 4) (Englisch)

368015

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Important Safety Advice

When using electrical appliances, basic precautions should

always be followed to reduce the risk of fire, electrical shock

and injury to persons, including the following:

If the appliance is damaged, check with the supplier before

installation and operation.

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower

or swimming pool.

Do not locate the heater immediately below a fixed socket

outlet or connection box.

Do not cover the heater. Do not place material or garments

on the heater, or obstruct the air circulation around the heater,

for instance by curtains or furniture, as this could cause

overheating and a fire risk.

This appliance is not intended for use by children or other

persons without assistance or supervision if their physical,

sensory or mental capabilities prevent them from using it

safely. Children should be supervised to ensure that they do

not play with the appliance.

Do not use this heater in series with a thermal control, a

program controller, a timer or any other device that switches

on the heat automatically, since a fire risk exists when the

heater is accidentally covered or displaced.

Ensure that furniture, curtains or other combustible material

are positioned no closer than 1 metre from the heater.

In the event of a fault unplug the heater.

Unplug the heater when not required for long periods.

Although this heater complies with safety standards, we do

not recommend its use on deep pile carpets or on long hair

type of rugs.

The appliance must be positioned so that the plug is

accessible.

If the supply cord is damaged it must be replaced by the

manufacturer or service agent or a similarly qualified person

in order to avoid a hazard.

Keep the supply cord away from the front of the heater.

Warning: In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on

and off by the utility.

General

Unpack the heater carefully and retain the packaging for possible

future use, in the event of moving or returning the fire to your supplier.

These models are designed to be free standing and are normally

positioned against a wall.

The fire incorporates a flame effect, which can be used with or without

heating, so that the comforting effect may be enjoyed at any time of

the year. Using the flame effect on its own only requires little electricity.

A choice of 1kW or 2kW heat output is provided by the fan heater,

which is located at the bottom of the unit.

Before connecting the heater check that the supply voltage is the

same as that stated on the heater.

Please note: Used in an environment where background noise

is very low, it may be possible to hear a sound which is related

to the operation of the flame effect. This is normal and should

not be a cause for concern.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED.

This heater must be used on an AC ~ supply only and the voltage

marked on the heater must correspond to the supply voltage.

Before switching on, please read the safety warnings and operating

instructions.

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Controls - see Fig. 2

These main ON/OFF switch must first be turned ON to operate any

of the other controls.

Setting Operation Indication

Flame Effect Press the ‘I’ button once Bottom Neon

Flame Effect & 1kW heat Press the ‘I’ button again Bottom & middle neon

Flame Effect & 2kW heat Press the ‘I’ button again All 3 neons

To turn off any of the Press the’O’button once.

settings

LED indicators

- see Fig. 6

Three LED’s as shown in Fig. 6 indicate the setting for a couple of

seconds every time you change the setting.

One LED means ON (flame effect only, no heat), two LED’s means

1kW heat and all three LED’s are on to indicate full 2kW heat setting.

Remote control - see Fig. 7

The maximum range of use is ~ 15metres.

The buttons on the remote control have the same function as the

swiches on the heater.

For details on the function please refer to the ‘Controls’ section above.

Warning: It takes time for the receiver to respond to the transmitter.

Do not press the buttons more than once within two seconds for correct

operation.

Battery information - see Fig. 7

1. Slide open the battery cover on the back of the remote control

2. Install AAA batteries into the remote control

3. Replace the battery cover.

Discard leaking batteries

Dispose of batteries in the proper manner according to provincial and

local regulations.

Any battery may leak electrolyte if mixed with a different battery type,

if inserted incorrectly; if all the batteries are not replaced at the same

time; if disposed of in a fire, or if an attempt is made to charge a

battery not intended to be recharged.

Lamp Replacement - see Fig. 3, Fig. 4 and Fig. 5

The lamps are located behind the back panel. To gain access to the

lamps, the screws indicated in Fig. 3 which secure the back panel,

must be removed.

Remove and slide out panel as indicated on Fig. 4.

Remove the defective lamp by unscrewing it as shown in Fig. 5.

Replace with a 60W E14 SES Clear candle lamp. Take care not to

over-tighten the lamp.

Refit the back panel and secure with the screws.

Thermostat (T) - see Fig. 2

In order to maintain a certain room temperature, set the controller to

‘max.’. Operate the appliance at full power until the required room

temperature is reached. Set back the thermostatic controller until the

appliance switches off with an audible “click”. This temperature will

be kept almost constant by the thermostatic control switching on and

off automatically.Please note that the appliance can only be switched

on when the thermostat setting is higher then the room temperature.

Thermal Safety Cut-out

The built-in overheat cut-out switches off the appliance automatically

in the event of a fault. If this occurs switch off the appliance or

disconnect the mains plug from the socket. Remove any obstructions

which may have caused the overheating. After a short cooling down

phase, the appliance is ready for use again. If the fault should occur

again, unplug the appliance and contact your local dealer.

grille of the fan heater.

- Stockbridge, SKG20BL

- Chevalier, CHV20

Recycling

For electrical products sold within the European

Community.

At the end of the electrical products useful life it should

not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority

or retailer for recycling advice in your country.

Dimplex stockbridge Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex stockbridge

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info