Bedienungsanleitung Dimplex VFE20K (Seite 45 von 52) (Deutsch, Englisch)

798167

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

www.dimplex.eu 2007/A EN-19

Commissioning English

9. Commissioning

9.1. Minimum tests

After the heating device has been fully installed and

connected, you can carry out a check to make sure it

is working correctly.

The following minimum tests must be carried out:

Isolation test with a voltage of at least 500 V. The

isolation resistance must be at least 0.5 MΩ.

Measurement of the power consumption.

Alternatively, a cold resistance measurement can

be carried out.

9.2. Re-installation

If a device has already been in operation, disassem-

bled and set up at a different location, all commission-

ing checks must be carried out again before heating

operation.

During the first charge of the storage heater after in-

stallation, the entire process, starting with the cold

state (room temperature) to the switch-off of the load

controller, must be monitored by a qualified specialist.

Determine the amount of energy used by the heating

device during this process in kWh. This must not be

more than 125% of the rated charging stated on the

rating plate.

NOTE

During installation, check that the thermal insulation

was not damaged during transport.

Damaged thermal insulation must be replaced with an

identical part before the heating device is used again!

9.3. Installer menu

The commissioning of the storage heater by the spe-

cialist takes place via the installer menu. First, the fol-

lowing entries must be made:

Current time, date

DST = summer/winter time switch,

Key tone on/off.

Once the entries have been made, the user main

menu appears. The timer times listed below are set at

the factory. They can be adjusted at any time.

The functions described below can be set in the in-

staller menu.

Calling up the installer menu

Hold down the Menu key. The display initially

switches to the CHARGING menu. Continue to hold

the key (for approx. 3 seconds in total). The display

switches to the main menu.

P9 - operation on central charge control

NOTE

No setting is required if the device is operated without

central charge control.

Press and hold the MENU, ENTER and BACK key

for approx. three seconds. PIN code 0000 flashes.

Confirm the PIN code four times with the ENTER

key. Display P9 flashes.

Select display P9. P9 flashes.

Press the ENTER key. OFF flashes.

Use the   keys to select ON. ON flashes.

Press the ENTER key. Display DC flashes.

NOTE

Display DC/AC stands for the control signal of the

central control device. Either DC or AC must be se-

lected depending on the type used.

Comfort 1 Comfort 2 Comfort 3 Comfort 4

06:30 -

09:30

11:00 -

13:00

15:00 -

17:00

18:00 -

21:00

No. Function Explanation

P9 Central charge

control

Yes/No,

If yes: AC/DC,

If AC: Duty cycle in percent

P10

External room

temperature con-

troller

Yes/No

P11 auxiliary heating Yes/No

P12 Release signal currently without function

P13 Release manual

Define time window for

manual release.

See “P12 - release signal”

on page 21.

P14

Reaction to failing

central charge

control signal

100% or 0% charge in case

of failing signal.

No. Function Explanation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex VFE20K Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info