Bedienungsanleitung Dimplex Vivente VVT75 (Seite 5 von 24) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

798190

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Fitting panel – After Installation

The Back Panel can also be change after the product has been installed, a person of suitable

competency is required to carry out this task. Please follow the steps below.

1. Unplug product from Power Supply and remove front trim on unit. See Fig. 2

2. Remove Front Glass from product and store in a safe place. (A suction cup is provided to help

remove/place the front glass.) See Fig. 6

3. Remove Fuelbed ﬁxing screws, then remove Fuelbed. (Fig. 7)

4. Remove both Side Glasses by moving them out at the bottom, then sliding out to remove. Store

these in a safe place. (Fig. 8).

5. Remove plastic Inner Screen by tilting it from the base. (Fig.9)

6. Remove Back Inner Panel bracket (Fig. 10A), Inner Back panel can then be tilted and removed

from its housing. (Fig. 10B)

7. Replace with new Back Inner Panel, and reverse the steps set out above, to re-assemble the

product. Ensure Inner screen is reassembled correctly. (Smooth mirrored ﬁnish to face the front of

the product.)

Step 3: Installing the Product

CAUTION: Two people will be required for various steps of this procedure.

This product is designed to be installed into existing block wall or a custom-built studded wall

structure. Please consult a competent installer before undertaking this to ensure a safe and

secure installation. If installing into an existing chimney or ﬂue, please ensure that the chimney or

ﬂue is blocked o. This is to prevent up-draughts aecting product operation.

Electrical Requirements

NOTE: A dedicated, properly fused 13 Amp circuit is required, rated for the appropriate voltage

(230-240V). An isolation switch should also be incorporated in cases where the product plug is

inaccessible after installation.

WARNING: Construction and wiring must comply with local building codes and other applicable

regulations to reduce the risk of ﬁre, electric shock and injury to persons.

WARNING: To reduce the risk of ﬁre, electric shock or injury to persons, always use a licensed

electrician.

1. Using the product dimensions (Fig. 11), build a suitable structure for the product to ﬁt into.

Ensure that, when installed, the product is within 1m of a power outlet. Please refer to Electrical

Requirements section above for more details.

It is recommended that the base of the unit is installed between 200mm and 800mm from the

ﬂoor. This is to maintain an optimised viewing angle of the ﬁre eect. (See Fig. 12)

The product must not bear the weight of the ﬁnished wall located above it. Consider the use of a

lintel for appropriate support.

2.Using any combination of the three ﬁxing methods (Fig. 13 a,b,c), ﬁx the product to its supporting

structure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Vivente VVT75 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex Vivente VVT75

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info