Bedienungsanleitung Dimplex WI 100TU (Seite 22 von 64) (Deutsch, Englisch, Französisch)

798443

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

EN-8 452234.66.37 · FD 9205 www.dimplex.de

English

WI 50TU - WI 100TU

2) The three-core supply cable for the heat pump manager

(heating controller N1) is fed into the heat pump .

Connection of the control line to the control panel of the heat

pump via terminal X2: L/N/PE.

Details on the power consumption of the heat pump are

listed on both the product information sheet and the type

plate.

The (L/N/PE~230 V, 50 Hz) supply cable for the heat pump

manager must have a constant voltage. For this reason, it

should be tapped upstream from the utility blocking contac-

tor or be connected to the household current, as important

protection functions could otherwise be lost during a utility

block.

3) The utility blocking contactor(K22) with 3 main contacts (1/3/

5 // 2/4/6) and an auxiliary contact (NO contact 13/14)

should be dimensioned according to the heat pump output

and must be supplied by the customer.

The NO contact of the utility blocking contactor (13/14) is

looped from terminal strip X3/G to connector terminal X3/A1.

CAUTION! Extra-low voltage!

4) The contactor (K20) for the immersion heater (E10) of mono

energy systems (HG2) should be dimensioned according to

the radiator output and must be supplied by the customer. It

is controlled (230 V AC) by the heat pump manager via ter-

minals X2/N and X2/K20.

5) The contactor (K21) for the flange heater (E9) in the hot

water cylinder should be dimensioned according to the radi-

ator output and must be supplied by the customer. It is con-

trolled (230 V AC) by the heat pump manager via terminals

X2/N and X2/K21.

6) The contactors mentioned above in points 3, 4 and 5 are in-

stalled in the electrical distribution system. The mains cables

for the heating elements should be dimensioned and pro-

tected according to DIN VDE 0100.

7) All cables must be installed as permanent wiring.

8) The heat circulating pump (M13) is connected to terminals

X2/N and X2/M13.

9) The DHW loading pump (M18) is connected to terminals X2/

N and X2/M18.

10) The brine and/or well pump (M11) is connected to terminals

2/4/6 of K5 and PE.

11) A return sensor is integrated into the heat pump. The return

flow sensor must be installed in the immersion sleeve in the

manifold when a dual differential pressureless manifold is

used. The single-core wires are then connected to terminals

X3/GND and X3/ R2.1. Bridge A-R2 (situated between X3/

B2 and X3/1 when delivered) must then be moved to termi-

nals X3/1 and X3/2.

12) The external sensor (R1) is connected to terminals X3/GND

and X3/R1.

13) The domestic hot water sensor (R3) is included with the do-

mestic hot water cylinder and is connected to terminals X3/

GND and X3/R3.

All lines must be fed into the device from the back and secured

at the switch box using cable connectors. They must additionally

be secured with a strain relief.

8 Start-up

8.1 General

To ensure that start-up is performed correctly, it should only be

carried out by an after-sales service technician authorised by the

manufacturer. This may be a condition for extending the guaran-

tee. (see warranty service)

8.2 Preparation

Prior to commissioning, the following items need to be checked:

All connections of the heat pump must have been made as

described in Chapter 7.

The heat source system and the heating circuit must have

been filled and checked.

The strainer must have been fitted in the well water inlet of

the heat pump.

In the well water and heating circuits all valves that might im-

pair the proper flow must be open.

The settings of the heat pump manager must be adapted to

the heating installation in accordance with the instructions

contained in the controller's operating manual.

8.3 Procedure

The start-up of the heat pump is effected via the heat pump man-

ager.

ATTENTION!

Commissioning is to be effected in accordance with the installation and

operating manual of the heat pump manager.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex WI 100TU Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info