Bedienungsanleitung Dimplex WI 140TUR plus (Seite 22 von 72) (Deutsch, Englisch, Französisch)

798436

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

EN-4 452234.66.76 · FD 9912 www.gdts.one

English WI 140TUR+

3Basic device

The basic device consists of a ready-to-use heat pump for in-

door installation, complete with sheet metal casing, control

panel and integrated heat pump manager. The refrigeration cir-

cuit is "hermetically sealed" and contains the fluorinated refrig-

erant R410A included in the Kyoto protocol. Information on the

GWP value and CO2 equivalent of the refrigerant can be found

in the chapter Device information. The refrigerant is CFC-free,

non-ozone depleting and non-combustible.

All components required for the operation of the heat pump are

located in the control box. An external temperature sensor in-

cluding fixing accessories, a dirt trap and a flow rate switch, is

supplied with the heat pump. The voltage supply for the load

and control current must be provided by the customer.

The well water pump (to be provided by the customer) must be

controlled via the switch box. It must be equipped with a motor

protection device, if required.

The customer must provide hydraulic components for the well

water circuit.

1) Control

2) Evaporator

3) Liquefier

4) Compressor

5) Transport securing devices

6) Hot water liquefier

4 Accessories

4.1 Connecting Flanges

The use of flat-sealing connecting flanges allows the unit, as an

option, to be connected by means of flanges.

4.2 External four-way reversing

valve, Water circuit side

The external four-way reversing valve (Y12) enables optimised

heating and cooling operation of the reversible water-to-water

heat pump. The reversal of the flow direction ensures an opti-

mum flow through the heat exchanger on the secondary side,

both in heating operation and in the opposite direction in cool-

ing operation. The electrical actuator required for automatic

switching is controlled by the heat pump manager. (Max. per-

missible switching current 2A).

If the external four-way reversing valve is not used, the heat

outputs and the COPs are reduced as specified in the device in-

formation. With heating-only operation without an external

four-way valve, the hydraulic connection should be carried out

such that the heat exchanger is loaded in the opposite direction

(observe note in section 7.2 „Connection on heating and hot

water side“).

The external four-way reversing valve with a set time of max. 60

seconds, which is available as special accessory, ensures

switching of the water flow over the complete range of operat-

ing temperatures without any mixing losses.

The hydraulic and electrical circuit diagrams in the appendix

show the basic design. Detailed installation instructions are

provided with the four-way reversing valve.

4.3 Remote control

A remote control adds convenience and is available as a special

accessory. Operation and menu navigation are identical to

those of the heat pump manager. Connection takes place via an

interface (special accessories) with RJ 12 Western plug.

NOTE

In the case of heating controllers with a removable operating

element, this can also be used directly as a remote control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex WI 140TUR plus Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info