Bedienungsanleitung Dimplex WI 45TU (Seite 21 von 72) (Deutsch, Englisch, Französisch)

798221

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.glendimplex.de 452237.66.49a · FD 0108 EN-3

WI 35TU - WI 45TU English

3Basic device

The device consists of a heat pump for indoor installation wired

ready for use with metal casing, switch box and integrated heat

pump manager. The refrigeration circuit is "hermetically sealed"

and contains the fluorinated refrigerant R410A included in the

Kyoto protocol. Information on the GWP value and CO2 equiva-

lent of the refrigerant can be found in the chapter Device infor-

mation. The refrigerant is CFC-free, non-ozone depleting and

non-combustible.

All components required for the operation of the heat pump are

located in the switch box. An outside temperature sensor in-

cluding fixing accessories and a dirt trap are supplied with the

heat pump. The supply for the supply voltage and the control

voltage must be installed by the customer.

The circulating pumps included in the scope of supply must be

installed in accordance with the hydraulic diagrams (see Cap. 4

on page XX) or the development documents. The electrical

connection of the circulating pumps must be established in ac-

cordance with Cap. 7.5.3 on page 8.

The control wire of the primary pump (to be provided by the

customer) is to be connected to the control box. When so do-

ing, a motor protecting device is to be installed, if required.

The customer must provide hydraulic components for the well

water circuit.

1) Switch box

2) Evaporator

3) Liquefier

4) Filter dryer

5) Compressor 1

6) Compressor 2

7) Expansion valve

8) Economiser

4 Accessories

4.1 Remote control

A remote display adds convenience and is available as a special

accessory. Operation and menu navigation are identical to

those of the heat pump manager. Connection takes place via an

interface (special accessories) with RJ 12 Western plug.

NOTE

ºººº

In the case of heating controllers with a removable control

panel, this can also be used directly as a remote display.

4.2 Building management system

The heat pump manager can be connected to a building man-

agement system network via supplementation of the relevant

interface plug-in card. The supplementary installation instruc-

tions of the interface card must be consulted regarding the

exact connection and parameterisation of the interface.

The following network connections can be made on the heat

pump manager:

Modbus

EIB, KNX

Ethernet

CAUTION!

If the heat pump or circulating pumps are controlled

externally, a flow rate switch is required to prevent the

compressor from being switched on when there is no volume

flow.

5 Transport

A lift truck is suited for transporting the unit on a level surface.

Carrying straps may be used if the heat pump needs to be

trans-ported on an uneven surface or carried up or down stairs.

These straps can be passed directly underneath the pallet.

CAUTION!

The heat pump must not be tilted more than 45° (in any

direction).

45°

max.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex WI 45TU Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info