Bedienungsanleitung Dimplex Wickson (Seite 9 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Norwegisch)

706539

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

3. Lift replace and insert into opening (Fig. 9).

4. Use bubble level (supplied) to level the replace within

the framing. Adjust as required.

5. Drive four supplied mounting screws through the four

mounting holes located in each corner of the replace

chassis, into wall studs (Fig. 9).

6. Refer to Front Glass Installation section for nal

installation procedures.

Flush Mount- see Fig. 10 & 11

CAUTION: Two people will be required for various steps

of this procedure.

1. Prepare a wall with a framed opening for the correct

model (Fig. 10)

• 34" Model: 33 in. (83.8 cm) wide x 18 ½ in. (47 cm)

high

• 50" Model : 49 in. (124.5 cm) wide x 18 ½ in. (47 cm)

high

• 74" Model: 73 in. (185.4 cm) wide x 18 ½ in. (47 cm)

high

NOTE: It is recommended that the bottom

of the unit not be mounted higher than 40 in.

(102 cm) from the ground to maintain an optimized viewing

angle of the ame.

WARNING: Do not attempt to wire your own new outlets

or circuits. To reduce the risk of re, electric shock or injury to

persons, always use a licensed electrician.

WARNING: Ensure that the circuit on which the replace

is to be installed has the power cut off at the service panel

until installation is complete.

2. Lift replace and insert into opening. The replace’s

mounting trim should be ush against the wall (Fig. 11).

3. Use the supplied bubble level to level the replace

within the framing, adjust as required.

4. Drive four supplied mounting screws through the four

mounting holes located on the inside surface of the

replace chassis, into wall studs (Fig. 11).

5. Refer to Front Glass Installation section for nal

installation procedures.

Front Glass Installation- see Fig. 12 & 13

1. Pour and evenly distribute the supplied media in the

Media tray of the firebox (Figure 12).

2. Carefully mount front glass assembly so that the front

glass hooks hang on the front glass mounts on the

fireplace (Figure 12).

3. Use the supplied four Phillips sheet metal screws

to fasten the glass assembly tabs to the fireplace

(Figure 13).

Remote Control - See Fig. 3

The maximum range of use is ~ 5metres.

NOTE: It takes time for the receiver to respond to the

transmitter.

NOTE: The reciever for the remote control is located in

the display, aim the remote control in this direction when

inputting commands.

Do not press the buttons more than once within two

seconds for correct operation.

Battery Information - See Fig. 3

1. To activate the remote control remove the clear battery

isolation strip at the base of the remote control, which

is used to ensure your remote control reaches you fully

charged.

2. To replace the remote control battery, turn over the

remote control, and follow the diagram embossed on the

remote control

3. Only use CR2025 or CR2032 size of batteries.

Thermal Safety Cut-out

The built-in overheat cut-out, switches off the appliance

automatically in the event of a fault! Should this occur

switch off the appliance or disconnect the mains plug

from the socket.

Remove any obstructions which may have caused the

overheating. After a short cooling down phase, the

appliance is ready for use again! If the fault should occur

again, contact your local dealer!

WARNING: In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched

on and off by the utility.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Light Emitting Diode

This re is tted with LED (Light Emitting Diode) lamps. These

LED lamps are maintenance-free and should not require

replacing during the life of the product.

Cleaning

WARNING: ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use

abrasive cleaners. The glass viewing screen should be

cleaned carefully with a soft cloth.

DO NOT use proprietary glass cleaners.

To remove any accumulation of dust or uff the soft brush

attachment of a vacuum cleaner should occasionally be

used to clean the outlet grille of the fan heater.

WARNING: do not operate the product without the grille

and outer glass in position as this may effect the operation

of the heater.

Recycling

For electrical products sold within the European

Community. At the end of the electrical products

useful life it should not be disposed of with

household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer

for recycling advice in your country.

After Sales Service

Should you require after sales service or should you need

to purchase any spares, please contact the retailer from

whom the appliance was purchased or contact the

service number relevant to your country on the warranty

card.

Please do not return a faulty product to us in the rst

instance as this may result in loss or damage and delay

in providing you with a satisfactory service. Please retain

your receipt as proof of purchase.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Wickson Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info