Bedienungsanleitung Dirt Devil M 2011 - Centrino XL3 (Seite 15 von 24) (Deutsch, Englisch, Französisch)

500165

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 Troubleshooting

5.1 Before you send in the appliance

Before contacting your authorised Royal dealer, Royal service partner or appliance market, first follow the procedure in the following table to check if you

can handle the problem yourself

5.2 Accessories/Spare Parts

Ordering address: Zpage 48, „International Service“.

5.3 Disposal

Dispose of the appliance in compliance with the environmental protection laws of your country. Electrical waste

may not be disposed of together with domestic waste. Use local old-appliance collection points instead. The

filters used are made from environment-friendly materials. You may dispose of them in your household waste.

5.4 Conditions of warranty

We grant a warranty of 24 months from the date of purchase for the appliance distributed by us. Within

this period we will either repair or replace the appliance or accessory (damages to accessories do not

automatically cause a replacement of the complete appliance) all defects due to manufacturing or materials at

no cost. Damages due to inappropriate use (operation on wrong voltage or type of current, connecting to

unsuitable power supplies, breakage, etc.) are exempt from warranty, as are normal wear and minor defects

that only negligibly influence the appliance's serviceability. Intrusions by unauthorised parties and the use of

spare parts not supplied by Royal Appliance invalidate the warranty. Consumable parts are not included in the

warranty and must be paid for! The warranty is only valid if the date of purchase has been acknowledged by

the dealer's stamp and signature on the warranty card or if a copy of the invoice or sales slip is included with

the sent-in appliance. Warranty work does not extend the warranty period nor does it constitute a claim for a

new warranty!

5.5 In case of a warranty

claim

Send us the appliance with its dust container empty and a short description of the defect in printed letters. Head

your accompanying letter with the notice "warranty claim". Send it including the warranty card or a copy of the

purchase slip. Address Zpage 48, „International Service“.

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the appliance and disconnect it from the mains before starting troubleshooting

Zchapter 3.1, „Switching off“.

Problem Possible cause Solution

The appliance will

not start

The power cord is not plugged in. Insert the plug into a mains socket and switch on the appliance Zchapter 2.2,

„Selecting the nozzle and vacuum cleaning“.

The socket does not carry current. Test the vacuum cleaner at another socket which you are sure carries current.

Power cord is damaged. Have the power cord replaced by Royal Appliance Customer Service, address,

Zpage 48, „International Service“.

The vacuum

cleaner stops

suddenly.

The overheating protection has tripped (possibly

due to blocked suction channels, extremely dirty

filters, or similar).

Switch the appliance off and pull the plug out of the socket.

Eliminate the cause of overheating (e.g. disassembling telescopic tube and suction

hose and removing the obstacle and/or cleaning filters). Wait for about 45 minutes.

After the appliance has cooled off, you may switch it on again.

Cleaning indicator

(Fig. 1/14) lights

up.

The dust container is full. Empty / clean the dust container Zchapter 3.4, „Emptying and cleaning the dust

container“.

The results are

unsatisfactory in

spite of the

appliance working

correctly.

The bypass vent (Fig. 1/6) is open. Close the bypass vent (Fig. 1/6).

The nozzle you are using does not suit the

flooring.

Change the nozzle, Zchapter 2.2, „Selecting the nozzle and vacuum cleaning“,

step 1.

The "carpet/hard floor" selector (Fig. 5) is in the

wrong position for the particular type of floor.

Set the "carpet/hard floor" selector (Fig. 5) to the correct position for the type of

floor, Zchapter 2.2, „Selecting the nozzle and vacuum cleaning“.

The power setting does not suit the flooring. Set the power to the setting suggested for the flooring, Zchapter 2.2, „Selecting

the nozzle and vacuum cleaning“, step 6.

The dust container is full. Empty / clean the dust container Zchapter 3.4, „Emptying and cleaning the dust

container“.

The filter is dirty. Clean the respective filter, Zchapter 4.2, „Checking and cleaning the cyclone“,

Zchapter 4.3, „Cleaning / changing the laminar motor protection filter“ or Zchapter

4.4, „Cleaning / changing the exhaust filter“.

Nozzle, telescopic tube or suction hose are

blocked.

Remove the obstacle. If necessary, use a long wooden stick (e.g. a broomstick) to

do this.

Item number Description

2700001 3-piece filter set (1 foam plastic motor protection filter +

1 laminar motor protection filter + 1 exhaust filter)

2700002 1 cyclone

M203-4 1 parquet brush

M208-8 1 turbo brush

M2011-4_Centrino XL3_7lang_20110615.pdf 15 15.06.2011 18:22:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil M 2011 - Centrino XL3 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info