Bedienungsanleitung Dirt Devil m 3884 1 magnum mpr2 (Seite 15 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

321068

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 Maintenance

5.3 Cleaning the exhaust filter

1. Switch off the appliance, Zchapter 4.3, „Switching off“.

2. Push the release catches of the exhaust filter cover down (Fig. 13/A)

and fold down the exhaust filter cover.

3. Remove the exhaust filter pulling by the two ears provided for this

(Fig. 13/B).

4. Remove residual dust with a soft brush, e.g. the supplied furniture

brush.

5. If the filter element is still dirty after this procedure, thoroughly rinse it

by hand in running water until all dirt is gone.

6. If the exhaust filter is damaged, deformed or too soiled, replace it

(ordering information Zchapter 5.4, „Spare parts and accessories“).

7. Reinsert the new/cleaned exhaust filter into its receptacle using the two

ears provided for this (Fig. 14/A).

8. Fit the exhaust filter cover on the bottom side first (Fig. 14/B) and then

fold it in upwards. You will feel and hear it snap into place.

5.4 Spare parts and accessories

 Ordering address: ZPage 48, „International Service“

 Further information: Z www.dirtdevil.de

 The following accessories and spare parts can be reordered:

5.5 Before you send in the appliance

Before contacting your Royal dealer, Royal service partner or appliance

market or sending in the appliance, first follow the procedure in the

following table to check if you can solve the problem yourself.

ATTENTION:

The filter element is washable, but it may not be cleaned in dishwashers

or washing-machines. Also, do not use detergents or brushes with hard

bristles to clean the filters. After rinsing the filter element, let it dry for

approx. 24 hours at room temperature. Only put it back into the

appliance when it is completely dry.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have acquired by reordering.

Item number Description

3884001 Filter set 5 pcs, consisting of 1 central lamellae filter,

1 motor protection filter, 1 exhaust filter and 2 filter fleeces

M203 1 parquet brush

M209 1 turbo brush

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting trouble-

shooting Zchapter 4.3, „Switching off“.

Problem Possible cause / solution

The appli-

ance will

not start.

The socket does not carry current.

Test the vacuum cleaner at another socket which you are

sure carries current.

Power cord is damaged.

Have the cord replaced by the Royal Appliance Customer

Service (ZPage 48, „International Service“).

The vacu-

um cleaner

stops sud-

denly.

The overheating protection has tripped (possibly due to

blocked suction channels, filters, or similar).

Switch the appliance off and pull the plug out of the socket.

Remove the cause of overheating (e.g. by disassembling

telescopic tube and suction hose and removing the obstacle

and/or cleaning filters). Wait for about 45 minutes. After the

appliance has cooled off, you may switch it on again.

Cleaning in-

dicator

(Fig. 1/11)

lights up.

The central lamellae filter is dirty.

Clean the central lamellae filter, Zchapter 5.2, „Cleaning

central lamellae filter and motor protection filter“.

The dust container is full.

Empty the dust container, Zchapter 5.1, „Emptying and

cleaning the dust container“.

The clean-

ing results

are unsatis-

factory in

spite of the

appliance

working

correctly.

The bypass vent (Fig. 1/20) is open.

Close the bypass vent .

The attached nozzle is unsuitable.

Change the nozzle, Zchapter 3.2, „Selecting the proper

nozzle“.

The suction power you set is unsuitable.

Adjust the suction power control to suit the flooring,

Zchapter 4.2, „Vacuum cleaning“, step 4.

The position of the "carpet/hard floor" selector (Fig. 1/2) is

unsuitable.

Set the "carpet/hard floor" selector to the correct position for

the type of floor, Zchapter 4.2, „Vacuum cleaning“, step 5.

The dust container is full.

Empty / clean the dust container Zchapter 5.1, „Emptying

and cleaning the dust container“.

The filter is dirty.

Clean the respective filter Zchapter 5.2, „Cleaning central

lamellae filter and motor protection filter“ or Zchapter 5.3,

„Cleaning the exhaust filter“.

Nozzle, telescopic tube or suction hose are blocked.

Remove the obstacle. If necessary, use a long wooden stick

(e.g. a broomstick) to do this.

NOTE:

If you cannot solve the problem following these instructions, contact the

Royal Appliance customer service (ZPage 48, „International Service“).

Problem Possible cause / solution

Magnum MPR2.book Seite 15 Freitag, 18. März 2011 6:53 18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil m 3884 1 magnum mpr2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info