Bedienungsanleitung Dirt Devil m 5021 0 infinity v8 (Seite 14 von 29) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

320873

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

4 Operation

 This is how to attach the nozzles:

1. Switch off the vacuum cleaner and pull the plug from the mains socket.

2. Pull the attached nozzle from the telescopic tube.

3. Put the desired nozzle onto the bottom end of the telescopic tube (Fig. 8/1) or if necessary directly onto the

handle (Fig. 8/2).

4. Attach the nozzles no longer required to the accessory bracket, as far as this is possible (Fig. 9).

4Operation

4.1 Before starting

vacuum-cleaning

4.2 Vacuum cleaning 1. Attach the desired nozzle ZChapter 3.2, "Assembly" or ZChapter 3.3, "Using further nozzles (accessories)".

2. Pull out the cord by the plug up to the yellow mark (Fig. 10/1).

3. Switch on the cylinder vacuum cleaner with the on/off switch (Fig. 11/1).

4. Set the nozzle switch to "carpet" or "hard floor" (Fig. 12/1) according to the floor to be cleaned:

- Hard floor (Fig. 12/a)

Laminate, tiles, PVC, etc.

- Carpet (Fig. 12/b)

Short- and deep-pile carpets, rugs, etc.

5. When working with the cylinder vacuum cleaner, pull if after you like a sleigh.

WARNING:

Danger of injury! Only assemble the appliance if it is not connected to the power supply. Otherwise the machine

might start up and parts of your body, hair or pieces of clothing might be sucked in.

ATTENTION:

Use only intact nozzles. Damaged nozzles may scratch or damage surfaces and objects.

ATTENTION:

Using the cylinder vacuum cleaner without a nozzle attached increases the danger of accidentally sucking in objects.

WARNING:

Danger of injury! A damaged appliance must never be used. Check the cylinder vacuum cleaner and the power

cord before each use.

ATTENTION:

Only use the cylinder vacuum cleaner with all filters intact, in dry condition and correctly placed. Make sure that the

openings of the vacuum cleaner are not clogged.or obstructed. Otherwise the vacuum cleaner might be damaged.

ATTENTION:

Check the requirements of your floorings before using the vacuum cleaner. Follow the recommendations of the

flooring manufacturers.

NOTE:

Your cylinder vacuum cleaner is equipped with a safety switch to prevent overheating. It automatically cuts off

the power supply if the motor is overheated. If this happens switch off the cylinder vacuum cleaner and

disconnect it from the mains. Remove the cause of the overheating. Wait for about 45 minutes. After it has

cooled off, you may use the cylinder vacuum cleaner again.

WARNING:

Danger of electric shock! If the red marking (Fig. 10/2) is visible, retract the cord by pressing the retract button

(Fig. 11/2) to pull in the cable up to the yellow mark again. Otherwise the cord might break.

WARNING:

Danger of tripping! Pull out the power cord only as far as necessary. After vacuuming, roll up the power cord

again by pressing the cable retract button (Fig. 11/2) immediately..

NOTE:

With the bypass vent (Fig. 13/1) you can quickly reduce suction power if less suction is needed, e.g. to release

objects accidentally sucked in.

V8.book Seite 14 Mittwoch, 6. April 2011 10:09 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil m 5021 0 infinity v8 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info