Bedienungsanleitung Dirt Devil M 7066 Cargo (Seite 15 von 24) (Deutsch, Englisch, Französisch)

500172

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 Maintenance

5.3 Cleaning the exhaust filter

 Check the exhaust filter each time you check the motor protection filter,

ZChapter 5.2, ‘Cleaning the motor protection filter’.

 Clean the exhaust filter as soon as you see it is dirty.

 Replace the exhaust filter as soon as it deforms or is damaged

(ZChapter 5.4, ‘Spare parts and accessories’).

1. Switch off the appliance, ZChapter 4.3, ‘Switching off’.

2. Push down the release catch of the exhaust filter cover and fold down

the cover (Fig. 13/A).

3. Remove the exhaust filter from its holder (Fig. 13/B).

4. Thoroughly rinse the exhaust filter by hand under clear, cold or luke-

warm running water.

5. Put the new / cleaned and completely dry exhaust filter back into its re-

ceptacle (Fig. 13/B).

6. Fit the exhaust filter cover on the bottom side first (Fig. 14/A) and then

push it into its receptacle (Fig. 14/B). It might be easier if you push

down the release catch in the process (Fig. 13/A).

7. Check the exhaust filter cover for correct fit.

5.4 Spare parts and accessories

 Orders by fax or post: ZPage 48, ‘International Service’

 Further information: Z www.dirtdevil.de

5.5 Recommendation

We recommend: Swirl

AirSpace

Y50

dust filter bags with MicroPor

filtration

Swirl



, AirSpace



, MicroPor



and Y50



are registered trade marks of a company of the Melitta group and used with their permission.

5.6 Before you send in the appliance

Before contacting us (ZPage 48, ‘International Service’) or even sending

the appliance to us, use the table to check whether you can correct the

problem yourself.

click!click!click!

ATTENTION:

The filters are washable, but not suitable for cleaning in washing

machines or dishwashers. Do not use cleaning agents for cleaning.

Leave the filters to dry after cleaning them with water (approx. 24 hours

at room temperature). Only put them back into the appliance when they

are completely dry.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have purchased by reordering.

Item number Description

7000022 Set of 5 dust filter bags and 1 motor protection filter

7066002 1 exhaust filter

M203-4 1 parquet brush

M208-8 1 turbo brush

M219 1 mini turbo brush

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing ZChapter 4.3, ‘Switching off’.

Problem Possible cause / solution

Filter bag

change indi-

cator (Fig. 1/

4) appears in

the display

window.

The dust filter bag is full. Change the dust filter bag,

ZChapter 5.1, ‘Changing the dust filter bag’.

Nozzle, tube, or suction hose is blocked.

Remove the obstacle. If necessary, use a long wooden

stick (e.g. a broomstick) to do this.

The filters are dirty. Clean the respective filter ZChapter

5.2, ‘Cleaning the motor protection filter’ or ZChapter 5.3,

‘Cleaning the exhaust filter’.

The vacuum

cleaner stops

suddenly.

The overheating protection has tripped (possibly due to

blocked suction channels, filters, or similar). Switch the

appliance off and pull the plug out of the socket. Eliminate

the cause of overheating (e g. remove blockage). Wait for

about 45 minutes. After the appliance has cooled off, you

may switch it on again.

The cleaning

results are

unsatisfac-

tory in spite of

the appli-

ance work-

ing correctly.

The bypass vent (Fig. 1/20) is open. Close the bypass

vent (Fig. 1/20).

The power setting does not suit the flooring. Set the pow-

er to the setting suggested for the flooring, ZChapter 4.2,

‘Vacuum cleaning’, step 4.

The position of the ‘carpet/hard floor’ selector (Fig. 1/29)

is unsuitable. Set the ‘carpet/hard floor’ selector (Fig. 1/

29) to the correct position for the type of floor, ZChapter

4.2, ‘Vacuum cleaning’, step 5.

The attached nozzle is unsuitable. Change the nozzle,

ZChapter 3.2, ‘Assembly’.

The dust filter bag is full. Change the dust filter bag,

ZChapter 5.1, ‘Changing the dust filter bag’.

The filters are dirty. Clean the respective filter ZChapter

5.2, ‘Cleaning the motor protection filter’ or ZChapter 5.3,

‘Cleaning the exhaust filter’.

Nozzle, telescopic tube or suction hose is blocked. Re-

move the obstacle. If necessary, use a long wooden stick

(e.g. a broomstick) to do this.

Problem Possible cause / solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil M 7066 Cargo Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info